manualshive.com logo in svg

Siemens Brodersen MC55, Command Manual

Share
Download
Siemens Brodersen MC55 Command Manual Download Page 403

MC55_ATC_V04.00

Page 403 of 475

3/17/06

Confidential / Released

 

17.4

AT+CLVL Loudspeaker volume level

Syntax

Parameter Description

Loudspeaker Volume Level
0...4

(D)

Notes

• The write command can only be used in audio mode 2 - 6.
• The values of the volume steps are specified with the parameters 

<outCalibrate>

[0],...

<outCali-

brate>

[4] of the 

AT^SNFO

 command.

• As an alternative to 

AT+CLVL

, you can use 

AT^SNFO

 and 

AT^SNFV

. The parameter 

<level>

 is identical with

<outStep>

 used by both commands.

• Any change to 

<level>

 (or 

<outStep>

) takes effect in audio modes 2 to 6. That is, when you change

<level>

 (or 

<outStep>

) and then select another mode with 

AT^SNFS

, the same step will be applied.

The only exception is audio mode 1 which is fixed to 

<level>

=4 (or accordingly 

<outStep>

=4).

•

<level>

 (or 

<outStep>

) is stored non-volatile when the ME is powered down with 

AT^SMSO

 or reset with

AT+CFUN

=1,1.

Test Command

AT+CLVL=?

Response(s)

+CLVL: 

(list of supported

<level>

s)

OK

Read Command

AT+CLVL?

Response(s)

+CLVL: 

<level>

OK

ERROR

+CME ERROR: <err>

Write Command

AT+CLVL=

<level>

Response(s)

OK

ERROR

+CME ERROR: <err>

Reference(s)

PIN

ASC0 ASC1

MUX1

MUX2

MUX3 Charge

Last

GSM 07.07

!

%

%

%

%

%

!

!

!

<level>

(num)

Summary of Contents for Brodersen MC55




























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands