Siemens Brodersen MC55 Command Manual Download Page 426

Page: 426 / 475

MC55_ATC_V04.00

Page 426 of 475

3/17/06

Confidential / Released

18.

Hardware related Commands

The AT Commands described in this chapter are related to the MC55's hardware interface. More information

regarding this interface is available with the "MC55 Hardware Interface Description"

[2]

18.1

AT+CCLK Real Time Clock

Syntax

Parameter Description

Format is "yy/mm/dd,hh:mm:ss", where the characters indicate the two last digits of the year, followed by month,

day, hour, minutes, seconds; for example 6th of July 2005, 22:10:00 hours equals to "05/07/06,22:10:00"

Factory default is "02/01/01,00:00:00"

Notes

•

<time>

is retained if the device enters the Power Down mode via

AT^SMSO

•

<time>

will be reset to its factory default if power is totally disconnected. In this case, the clock starts with

<time>

= "02/01/01,00:00:00" upon next power-up.

• Each time MC55 is restarted it takes 2s to re-initialize the RTC and to update the current time. Therefore, it

is recommended to wait 2s before using the commands

AT+CCLK

and

AT+CALA

(for example 2s after

^SYSSTART has been output).

Test Command

AT+CCLK=?

Response(s)

Read Command

AT+CCLK?

Response(s)

+CCLK:

<time>

Write Command

AT+CCLK=

<time>

Response(s)

+CME ERROR: <err>

ERROR

Reference(s)

ASC0 ASC1

MUX1

MUX2

MUX3 Charge

Last

GSM 07.07

<time>

(str)

Summary of Contents for Brodersen MC55




























































































































































































































































































































































































































































































Search results

Summary of Contents for Brodersen MC55

Reviews:

Brands by name

Popular brands

Siemens Brodersen MC55, Command Manual

Search results

Summary of Contents for Brodersen MC55

Reviews:

Brands by name

Popular brands