manualshive.com logo in svg

Siemens Brodersen MC55, Command Manual

Share
Download
Siemens Brodersen MC55 Command Manual Download Page 446

MC55_ATC_V04.00

Page 446 of 475

3/17/06

Confidential / Released

 

Table 20.3: 

Star-Hash Command Response Parameters 

For exact specification of format and parameters for Star-Hash commands refer to GSM 02.04, Table 3.2 

[15]

and GSM 02.30, Annex C 

[16]

. 

Table 20.4: 

Star-Hash Commands for Supplementary Services 

PW

Password

-- 

C

Character of TE character set (e.g. asterics, hash 

or digit in case of USSD, or digits in case of held 

calls or multiparty calls)

--

Parameter

Meaning

<m>

Mode: 0 = not active, 1 = active 

<n>

Unsolicited result code: 0 = presentation disabled, 1 = presentation enabled 

<status>

Status: 0 = not active, 1 = active 

<class> 

Represents BS = basic service, refer to 

AT+CCFC

, 

AT+CLCK

 

<fac>

Facility lock, refer to 

AT+CLCK

 

<reason>

Call forwarding reason 

Star-Hash Code 

Abbreviations in Table 

20.1

 

Functionality 

* 

act 

Activate (except for CLIR, see list above)

** 

reg 

Register and activate

*# 

int 

Check status (interrogate)

# 

deact 

Deactivate (except for CLIR, see list above)

## 

eras 

Unregister and deactivate

Abbreviation

Meaning

Value

Summary of Contents for Brodersen MC55




























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands