Siemens Brodersen MC55 Command Manual Download Page 146

Page: 146 / 475

MC55_ATC_V04.00

Page 146 of 475

3/17/06

Confidential / Released

7.19

AT+CRLP Select radio link protocol parameters for originated
non-transparent data calls

The

AT+CRLP

write command sets radio link protocol (RLP) parameters used when non-transparent data calls

are originated. The read command returns the current settings for the supported RLP version 0.

Syntax

Parameter Description

Interworking window size (IWF to MS)
0...61

(&F)

Mobile window size (MS to IWF)
0...61

(&F)

Acknowledgement timer (T1 in 10 ms units)
48...[78]

(&F)

...255

Re-transmission attempts N2
1...6

(&F)

...255

Test Command

AT+CRLP=?

Response(s)

+CRLP:

(list of supported

<iws>

s), (list of supported

<mws>

s), (list of supported

<T1>

s), (list of

supported

<N2>

Read Command

AT+CRLP?

Response(s)

+CRLP:

<iws>

<mws>

<T1>

<N2>

Write Command

AT+CRLP=

[

<iws>

<mws>

<T1>

<N2>

]]]]

Response(s)

ERROR

+CME ERROR: <err>

Reference(s)

ASC0 ASC1

MUX1

MUX2

MUX3 Charge

Last

GSM 07.07

<iws>

(num)(&W)(&V)

<mws>

(num)(&W)(&V)

<T1>

(num)(&W)(&V)

<N2>

(num)(&W)(&V)

Summary of Contents for Brodersen MC55




























































































































































































































































































































































































































































































Search results

Summary of Contents for Brodersen MC55

Reviews:

Brands by name

Popular brands

Siemens Brodersen MC55, Command Manual

Search results

Summary of Contents for Brodersen MC55

Reviews:

Brands by name

Popular brands