MIPS MIPS32 74K Series Programming Manual Download Page 116

Page: 116 / 156

8.1 EJTAG on-chip debug unit

Programming the MIPS32® 74K™ Core Family, Revision 02.14

116

Where:

ASIDsup

: is 1 if the breakpoints can use ASID matching to distinguish addresses from different address spaces; on the

74K core that’s available if and only if a TLB is fitted.

BCN

: the number of hardware breakpoints available (two data, four instructions).

BS1-0, BSD3-0

: bitfields showing breakpoints which have been matched. Debug software has to clear down a bit after a

breakpoint is detected.

Then each EJTAG hardware breakpoint (“n” is 0-3 to select a particular breakpoint) is set up through 4-6 separate
registers:

•

IBCn, DBCn

: breakpoint control register shown at Figure 7-9 below;

•

IBAn, DBAn

: breakpoint address;

•

IBAMm, DBAMn

: bitwise mask for breakpoint address comparison. A "1" in the mask marks an address bit which

will be excluded from comparison, so set this zero for exact matching.

Ingeniously,

IBAMm[0]

corresponds to the slightly-bogus instruction address bit zero used to track whether the

CPU is running MIPS16 instructions, and allows you to determine whether an EJTAG I-breakpoint may apply
only in MIPS16 (or non-MIPS16) mode.

•

IBASIDn, DBASIDn

specifies an 8-bit ASID, which may be compared against the current

EntryHi[ASID]

field to

filter breakpoints so that they only happen to a program in the right "address space". The ASID check can be
enabled or disabled using

IBCn[ASIDuse]

DBCn[ASIDuse]

respectively - see Figure 7-9 and its notes below. ID

(so that the break will only affect one Linux process, for example).

The higher 24 bits of each of these registers is always zero.

•

DBVn, DBVHin

the value to be matched on load/store breakpoints.

DBCHin

defines bits 63-32 to be matched for

64-bit load/stores: the 32-bit

74K has 64-bit load/store instructions for floating point.

Note that you can disable data matching (to get an address-only data breakpoint) by setting the value byte-lane
comparison mask

DBCn[BLM]

to all 1s.

So now let’s look at the control registers in

Figure 8.15

Figure 8.14 Fields in the IBS/DBS (EJTAG breakpoint status) registers

29 28 27

24 23

4 3 2 1

DBS

ASID-

sup

BCN =

BS1-0

IBS

BCN =

BSD3-0

27. A JTAG hardware breakpoint for a real 64-bit CPU would have 64-bit

DBVn

registers, so wouldn’t need

DBVHin

Summary of Contents for MIPS32 74K Series





























































































































































Search results

Summary of Contents for MIPS32 74K Series

Reviews:

Related manuals for MIPS32 74K Series

Brands by name

Popular brands

MIPS MIPS32 74K Series, Programming Manual

Search results

Summary of Contents for MIPS32 74K Series

Reviews:

Related manuals for MIPS32 74K Series

Brands by name

Popular brands