MIPS MIPS32 74K Series Programming Manual Download Page 128

Page: 128 / 156

8.3 CP0 Watchpoints

Programming the MIPS32® 74K™ Core Family, Revision 02.14

128

8.3 CP0 Watchpoints

Some

core

s may be built with no EJTAG debug unit to save space, and some debug software may not know how to use

EJTAG resources. So it may be worth configuring the four non-EJTAG CP0 watchpoint registers. In 74K

core

s you

get two I-side and two D-side registers.

These registers provide the interface to a debug facility that causes an exception if an instruction or data access
matches the address specified in the registers. Watch exceptions are not taken if the CPU is already in exception mode
(that is if

Status[EXL]

Status[ERL]

is already set).

Watch events which trigger in exception mode are remembered, and result in a “deferred” exception, taken as soon as
the CPU leaves exception mode.

This CP0 watchpoint system is independent of the EJTAG debug system (which provides more sophisticated hard-
ware breakpoints).

The

WatchLo0-3

registers hold the address to match, while

WatchHi0-3

hold a bundle of control fields.

8.3.1 The WatchLo0-3 registers

Used in conjunction with

WatchHi0-3

respectively, each of these registers carries the virtual address and what-to-

match fields for a CP0 watchpoint.

Figure 8.22 Fields in the WatchLo0-3 Register

WatchLo0-3[VAddr]

: the address to match on, with a resolution of a doubleword.

WatchLo0-3[I,R,W]

: accesses to match: I-fetches, Reads (loads), Writes (stores). 74K

core

s have separate I- and D-side

watchpoints, so you’ll find that the I-side

WatchLo0-1[R]

and

WatchLo0-1[W]

is fixed to zero, while for the D-side-

only watchpoint,

WatchLo2-3[I]

will be zero.

8.3.2 The WatchHi0-3 registers

Figure 8.23 Fields in the WatchHi0-3 Register

WatchHi0-3[M]

: the

WatchHi0-3[M]

bit is set whenever there is one more watchpoint register pair to find; your soft-

ware should use it (starting with

WatchHi0

) to figure out how many watchpoints there are. That’s more robust than

reading the CPU manual...

WatchHi0-3[G,ASID]

WatchHi0-3[ASID]

matches addresses from a particular address space (the "ASID" is like that

in TLB entries) — except that you can set

WatchHi0-3[G]

("global") to match the address in any address space.

VAddr

R W

M G

ASID

Mask

R W

Summary of Contents for MIPS32 74K Series





























































































































































Search results

Summary of Contents for MIPS32 74K Series

Reviews:

Related manuals for MIPS32 74K Series

Brands by name

Popular brands

MIPS MIPS32 74K Series, Programming Manual

Search results

Summary of Contents for MIPS32 74K Series

Reviews:

Related manuals for MIPS32 74K Series

Brands by name

Popular brands