MIPS MIPS32 74K Series Programming Manual Download Page 109

Page: 109 / 156

74K™ core features for debug and profiling

109

Programming the MIPS32® 74K™ Core Family, Revision 02.14

Figure 8.4 Fields in the memory-mapped DCR (debug control) register

Where:

ENM

: (read only) reports CPU endianness (1 == big).

FDCImpl

: (read only) 1 if the Fast Debug Channel is available. See

Section 8.1.10 “Fast Debug Channel”

for details

DB/IB

: (read only) 1 if data/instruction hardware breakpoints are available, respectively. The 74K core has either 0 or 2

data breakpoints, and either 0 or 4 instruction breakpoints.

IVM:

(read-only) tells you if an inverted data value match on data hardware breakpoints is implemented.

DVM

: (read-only) tells you if a data value store on a data value breakpoint match is implemented.

RdVec

: If set, use the address specified in

DebugVectorAddr

address. If the probe is handling debug exceptions, it will continue to take precedence over this.

CBT

: (read-only) tells you if a complex breakpoint block is implemented.

PCS, PCR

PCS, PCSE,PCIM,PCnoASID: PCS

reads 1 if the PC sampling feature is available, as it can be on the 74K

core. Then

PCSE

enables PC sampling and

PCR

is a three-bit field defining the sampling frequency as one sample

every 2

(5+

PCR

) cycles.

PCnoASID

indicates or controls whether the ASID field is included in the sample.

PCIM

, if set-

table, enables only sampling the PC of instructions that missed in the instruction cache. See

Section 8.1.14, "PC

Sampling with EJTAG"

for details.

DAS, DASQ, DASE: DAS

reads 1 if the Data Address Sampling feature is available. If supported, this feature builds on

top of the PC sampling mechanisms to sample data addresses.

DASE

enables DAsampling and is not mutually exclu-

sive with

PCSE

DASQ

limits the data address samples to those addresses that match on data breakpoint 0.

INTE/NMIE

: set

DCR[INTE]

zero to disable interrupts in non-debug mode (it’s a separate bit from the various non-debug-

mode visible interrupt enables). The idea is that the debugger might want to step through kernel code or run kernel
subroutines (perhaps to discover OS-related information) without losing control because interrupts start up again.

DCR[NMIE]

masks non-maskable interrupt in non-debug mode (a nice paradox). Both bits are "1" from reset.

NMIP

: (read-only) tells you that a non-maskable interrupt is pending, and will happen when you leave debug mode (and

according to

DCR[NMIE]

as above).

SRE

: if implemented, write zero to mask soft-reset causes. This signal has no effect inside the 74K core but is presented

at the interface, where customer reset logic could be influenced by it.

: (read only) software-readable version of the probe-controlled enable bit

EJTAG_CONTROL[ProbEn]

, which you

could look at in

Figure 8.7

Res

ENM

Res

PCIM

PCno

ASID

DASQ DASe DAS

FDCI

mpl

IVM

DVM

RDVec

CBT

PCS

PCR

PCSE INTE NMIE NMIP SRE

Summary of Contents for MIPS32 74K Series





























































































































































Search results

Summary of Contents for MIPS32 74K Series

Reviews:

Related manuals for MIPS32 74K Series

Brands by name

Popular brands

MIPS MIPS32 74K Series, Programming Manual

Search results

Summary of Contents for MIPS32 74K Series

Reviews:

Related manuals for MIPS32 74K Series

Brands by name

Popular brands