MIPS MIPS32 74K Series Programming Manual Download Page 107

Page: 107 / 156

74K™ core features for debug and profiling

107

Programming the MIPS32® 74K™ Core Family, Revision 02.14

These fields are:

DBD

: exception happened in branch delay slot. When this happens

DEPC

will point to the branch instruction, which is

usually the right place to restart.

: debug mode - set on debug exception from user mode, cleared by

deret

Then some configuration and control bits:

NoDCR

: read-only - 0 if there is a memory-mapped

DCR

EJTAG unit implementing "dseg" at all implements

DCR

LSNM

: Set this to 1 if you want debug-mode accesses to "dseg" addresses to be just sent to system memory. This makes

most of the EJTAG unit’s control system unavailable, so will probably only be done around a particular load/store.

Doze

: before the debug exception, CPU was in some kind of reduced power mode.

Halt

: before the debug exception, the CPU was stopped - probably asleep after a

wait

instruction.

CountDM

: 1 if and only if the count register continues to run in debug mode. Writable for the 74K core, so you get to

choose. On some other implementations it’s read-only and just tells you what the CPU does.

IEXI

: set to 1 to defer imprecise exceptions. Set by default on entry to debug mode, cleared on exit, but writable. The

deferred exception will come back when and if this bit is cleared: until then you can see that it happened by looking at
the "pending" bits shown in

Figure 8.3

below.

EJTAGver

: read-only - tells you which revision of the specification this implementation conforms to. On the 74K core it

reads

for version 5.0. The full set of legal values are:

DExcCode

: Cause of any non-debug exception you just handled from within debug mode - following first entry to

debug mode, this field is undefined. The value will be one of those defined for

Cause[ExcCode]

, as shown in

Table

B.5

NoSSt

: read-only - reads 0 because single-step is implemented (it always is on MIPS Technologies cores).

SSt

: set 1 to enable single-step.

Figure 8.1 Fields in the EJTAG CP0 Debug register

21 20 19

18 17

15 14

6 5

DBD DM NoDCR LSNM Doze Halt

Count

pending

cause

EJTAGver

DExc

Code

NoSSt SSt OffLine 0

cause

(

0 Version 2.0 and earlier
1 Version 2.5
2 Version 2.6
3 Version 3.1
4 Version 4.0
5 Version 5.0

Summary of Contents for MIPS32 74K Series





























































































































































Search results

Summary of Contents for MIPS32 74K Series

Reviews:

Related manuals for MIPS32 74K Series

Brands by name

Popular brands

MIPS MIPS32 74K Series, Programming Manual

Search results

Summary of Contents for MIPS32 74K Series

Reviews:

Related manuals for MIPS32 74K Series

Brands by name

Popular brands