Korg NAUTILUS Series, Parameter Manual, Page: 675 / 961

GLOBAL > Wave Sequence 4–1: Seq. Parameter
665
Backwards/Forwards plays from the Start Step to the Loop
End, then backwards from the Loop End to the Loop Start,
and then forwards again to the Loop End, and so on.
Backwards plays from the Start Step to the Loop End, then
backwards from the Loop End to the Loop Start, and then
skips back to the Loop End, and so on.
For instance. let’s say that Repeat Times is set to 1 , Loop
Start is set to 2 , and Loop End is set to 4 . In this case, the
different Loop Directions work as shown below. The loop
itself is shown in
bold italic type
.
Forwards: 1, 2, 3, 4,
2, 3, 4,
5, 6.
Backwards: 1, 2, 3,
4, 3, 2,
5, 6.
Backwards/Forwards: 1, 2, 3, 4,
3, 2, 3, 4,
5, 6.
Repeat Times [Off, 1…127, INF]
This sets how many times the loop is repeated.
OFF means that the Loop Start , Loop End , and Loop
Direction parameters have no effect. The Wave Sequence
will play from the Start Step to the End Step , and then stay
at the End Step for the remainder of the note.
When this is set between 1 and 127 , the loop will repeat the
specified number of times. Once the repeats have finished, it
will play through to the
End Step , and then stay there for the
remainder of the note.
INF means that the loop will repeat continuously for the
duration of the note.
Note-On Advance [Off, On]
This parameter lets you advance the start point of the Wave
Sequence by one step with each new note-on. If
Repeat
Times is not set to Off , this will step through the loop,
paying attention to the loop direction and number of repeats.
For instance, let’s say that the Wave Sequence Start Step is
2 , and the End Step is 6 . Also, the Loop Start is set to 3 , the
Loop End is set to 5 , and the Loop Direction is set to
Forward .
If Repeat Times is Off , Note-On Advance will make the
Wave Sequence play as follows:
1st note: 2, 3, 4, 5, 6
2nd note: 3, 4, 5, 6
3rd note: 4, 5, 6
4th note: 5, 6
5th note: 6
6th note: 2, 3, 4, 5, 6
7th note: 3, 4, 5, 6
8th note: 4, 5, 6
9th note: 5, 6
10th note: 6
11th note: 2, 3, 4, 5, 6
etc…
If Repeat Times is 1 , Note-On Advance will make the
Wave Sequence play as follows:
first note: 2, 3, 4, 5, 3, 4, 5, 6
2nd note: 3, 4, 5, 3, 4, 5, 6
3rd note: 4, 5, 3, 4, 5, 6
4th note: 5, 3, 4, 5, 6
5th note: 3, 4, 5, 6
6th note: 4, 5, 6
7th note: 5, 6
8th note: 6
9th note: 2, 3, 4, 5, 3, 4, 5, 6
10th note: 3, 4, 5, 3, 4, 5, 6
11th note: 4, 5, 3, 4, 5, 6
12th note: 5, 3, 4, 5, 6
13th note: 3, 4, 5, 6
14th note: 4, 5, 6
15th note: 5, 6
etc…
Finally, if Repeat Times is 1 , Note-On Advance will make
the Wave Sequence play as follows. Note that the Wave
Sequence never returns to the start step, since it’s outside of
the loop:
first note: 2, 3, 4, 5, 3, 4, 5, 3, 4, 5, 3, 4, 5…
2nd note: 3, 4, 5, 3, 4, 5, 3, 4, 5, 3, 4, 5…
3rd note: 4, 5, 3, 4, 5, 3, 4, 5, 3, 4, 5…
4th note: 5, 3, 4, 5, 3, 4, 5, 3, 4, 5…
5th note: 3, 4, 5, 3, 4, 5, 3, 4, 5…
6th note: 4, 5, 3, 4, 5, 3, 4, 5…
7th note: 5, 3, 4, 5, 3, 4, 5…
8th note: 3, 4, 5, 3, 4, 5…
9th note: 4, 5, 3, 4, 5, 3, 4, 5…
10th note: 5, 3, 4, 5, 3, 4, 5…
etc…
Note: When Note-On Advance is On , Start Step
modulation is disabled.
Note-On Advance and Key Sync
Note-On Advance is also affected by the setting of the Key
Sync parameter.
If Key Sync is On , the start point will advance by one step
for each note.
If Key Sync is Off , the start point will advance by one step
for each new phrase. For more information, see “Key Sync,”
on page 663.
4–1d: Modulation
Position
AMS [List of AMS Sources]
This selects a modulation source to offset the Wave
Sequence from its current position. The Wave Sequence will
continue to progress through its steps during position
modulation. To sweep through a sequence manually, set
“Run,” above, to
Off .
If Position AMS changes by a large value over a small
amount of time, it will skip intermediate steps if necessary.
For a list of AMS sources, see “Alternate Modulation Source
(AMS) List” on page 901.