Korg NAUTILUS Series, Parameter Manual, Page: 713 / 961

MEDIA: Page Menu Commands Load selected
703
Load .PCG
Data in the .PCG file will be loaded.
1. Use the “Load ****** .SNG too”, “Load ****** .KSC
too” and check boxes to select the .SNG file and .KSC
file.
If this file does not exist in the current directory, load it as
described under “If a file to be loaded cannot be found, or
when loading a file that was saved across media” on
page 702.
2. In “.PCG Contents,” specify the data to be loaded.
All : Load all data from the .PCG file.
Bank A-T: Load only the data of the specified bank. In
this case, use “To” to specify the load destination bank.
When you press OK, the Combinations, Programs, Drum
Kits, and Wave Sequences of the specified bank will be
loaded to the destination bank. Global settings will not be
loaded.
Within the loaded data, all bank references (from
Combinations to Programs, and from Programs to Wave
Sequences and Drum Kits) will be adjusted automatically
to match the destination bank. For instance, if you load
USER-B into USER-GG, Combi Timbres which
previously referred to Programs in USER-B will be
changed to USER-GG. Only references to the original
bank will be adjusted; for instance, if you load USER-B,
references to INT-F will remain unchanged.
If a .SNG file is loaded simultaneously, banks will also be
adjusted for both Tracks and any Bank Change messages
within the sequencer data.
Note that types (HD-1 or EXi) of the loaded and
destination banks do not matter;
Note that it doesn’t matter whether the loaded bank is
HD-1 or EXi; the system will automatically set the
destination bank’s type appropriately.
If the specified bank is not included in the .PCG file, the
error “No readable data” will appear, and the load
operation will be halted.
3. If “Load ****** .SNG too” is checked, you can use
“Select .SNG Allocation” to specify how song data
within the .SNG file will be loaded.
.SNG Allocation
Append : The data will be loaded into song numbers
starting after the last song in memory which contains
data. The song data within the .SNG file that is being
loaded will be packed into the available locations. (See
diagram below)
Select this method when you wish to load song data from
drive without erasing the song data that is already in
memory.
The region data used by the song’s audio tracks will be
loaded following the last existing region number, with
valid data packed into each consecutive location. (See
diagram below) At this time, the region numbers of the
song will be reassigned so that the songs in the .SNG file
that use region data will correspond correctly to the
region data.
Clear: Song data already in internal memory will be
completely erased, and the song data will be loaded in the
configuration that existed when it was saved. (See
diagram below)
Select this when you want to reproduce the saved state
immediately after power-on, etc.
4. “.KSC Allocation” is valid if “Load ********.KSC
too” has been checked.
This specifies how the Multisamples, Samples, and Drum
Samples in the .KSC file will be loaded.
Append will leave all currently-loaded SAMPLING
mode, EXs, and User Sample Bank data intact.
SAMPLING mode Multisamples and Samples will be
loaded into the next available vacant numbers following
the existing data. (See diagram below.)
If the PCG’s Programs, Wave Sequences, and Drum Kits
use the KSC’s SAMPLING mode data, the system will
automatically remap the Multisample and Sample
references so that everything plays correctly.
Clear Sampling mode Data will erase all Multisamples
and Samples from SAMPLING mode, and load the data
in the same configuration with which it was saved.
Existing EXs and User Sample Bank data is left intact.
Clear All is similar to Clear Sampling mode Data ,
above, but also un-loads existing EXs and User Sample
Bank data before loading the new .KSC file. This frees up
the most memory for the new .KSC.
You can use the information at the bottom of the dialog
box, including
Memory Required , (Memory) Available ,
and Enough slots for Samples & MS , to determine
whether or not you need to free up room for the new
.KSC.
SNG000
SNG001
SNG005
SNG003
.SNG file to load
SNG000
SNG002
SNG003
SNG000
SNG002
SNG005
SNG003
SNG000
SNG001
SNG005
SNG003
SNG004
SNG007
SNG006
SNG000
SNG001
SNG005
SNG003
SNG000
SNG002
SNG003
Append
Clear
Internal memory of the
KRONOS after loading Internal memory of the
KRONOS before loading