Keysight Technologies DSO-X 2014A User Manual Download Page 191

Page: 191 / 378

Acquisition Control

Keysight InfiniiVision 2000 X-Series Oscilloscopes User's Guide

191

Infinite Persistence with Segmented Memory

When data has been acquired to segmented memory, you can also turn on infinite

persistence (in the Display Menu) and press the

Analyze Segments

softkey to create

an infinite persistence display. The

Analyze Segments

softkey appears when the

acquisition is stopped and the segmented memory feature is on.

Segmented Memory Re-Arm Time

After each segment fills, the oscilloscope re-arms and is ready to trigger in about

8 µs.

Remember though, for example: if the horizontal time per division control is set to

5 µs/div, and the Time Reference is set to

Center

, it will take at least 50 µs to fill all

ten divisions and re-arm. (That is 25 µs to capture pre-trigger data and 25 µs to

capture post-trigger data.)

Saving Data from Segmented Memory

You can save either the currently displayed segment (

Save Segment - Current

), or all

segments (

Save Segment - All

) in the following data formats: CSV, ASCII XY, and

BIN.

Summary of Contents for DSO-X 2014A



























































































































































































































































































































































































Search results

Summary of Contents for DSO-X 2014A

Reviews:

Related manuals for DSO-X 2014A

Brands by name

Popular brands

Keysight Technologies DSO-X 2014A, User Manual

Search results

Summary of Contents for DSO-X 2014A

Reviews:

Related manuals for DSO-X 2014A

Brands by name

Popular brands