Keysight Technologies DSO-X 2014A User Manual Download Page 44

Page: 44 / 378

Keysight InfiniiVision 2000 X-Series Oscilloscopes User's Guide

Getting Started

Figure 1

Interpreting the oscilloscope display

Status line

The top line of the display contains vertical, horizontal, and trigger setup

information.

Display area

The display area contains the waveform acquisitions, channel identifiers, and

analog trigger, and ground level indicators. Each analog channel's information

appears in a different color.
Signal detail is displayed using 256 levels of intensity. For more information

about viewing signal detail see

"To adjust waveform intensity"

page 125.
For more information about display modes see

Chapter 8

, “Display Settings,”

starting on page 125.

Information area

The information area normally contains acquisition, analog channel, automatic

measurement, and cursor results.

Menu line

This line normally contains menu name or other information associated with the

selected menu.

Analog channel
sensitivity

Status line

Analog
channels
and ground
levels

Trigger level

Digital channels

Softkeys

Menu line

Trigger point,
time reference

Delay
time

Time/
div

Run/Stop
status

Trigger
type

Trigger
source

Measurements

Trigger level or
digital threshold

Information area

Cursors defining
measurement

Summary of Contents for DSO-X 2014A



























































































































































































































































































































































































Search results

Summary of Contents for DSO-X 2014A

Reviews:

Related manuals for DSO-X 2014A

Brands by name

Popular brands

Keysight Technologies DSO-X 2014A, User Manual

Search results

Summary of Contents for DSO-X 2014A

Reviews:

Related manuals for DSO-X 2014A

Brands by name

Popular brands