manualshive.com logo in svg

Keysight Technologies DSO-X 2014A, User Manual

The Keysight Technologies DSO-X 2014A is a high-performance oscilloscope designed for accurate measurements and analysis. To make the most of its features, be sure to download the free User Manual from manualshive.com. This manual provides detailed instructions on how to operate and maximize the capabilities of this powerful tool.

Share
Download
background image

108

Keysight InfiniiVision 2000 X-Series Oscilloscopes User's Guide

6

Digital Channels

 

The sizing control lets you spread out or compress the digital traces vertically on 

the display for more convenient viewing.

To switch a single channel on or off

1

With the Digital Channel Menu displayed, rotate the Entry knob to select the 

desired channel from the popup menu.

2

Push the Entry knob or press the softkey that is directly below the popup menu 

to switch the selected channel on or off.

To switch all digital channels on or off

1

Press the 

[Digital]

 key to toggle the display of digital channels. The Digital 

Channel Menu is displayed above the softkeys.

If you want to switch the digital channels off, and the Digital Channel Menu is not 

already displayed, you must push the 

[Digital]

 key twice to switch the digital 

channels off. The first push displays the Digital Channel Menu, and the second 

push switches the channels off.

To switch groups of channels on or off

1

Press the 

[Digital]

 key on the front panel if the Digital Channel Menu is not 

already displayed.

2

Press the 

Turn off

 (or 

Turn on

) softkey for the 

D7 - D0

 group.

Each time you press the softkey, the softkey's mode toggles between 

Turn on

 and 

Turn off

.

To change the logic threshold for digital channels

1

Press the 

[Digital]

 key so that the Digital Channel Menu is displayed.

2

Press the 

Thresholds

 softkey

Summary of Contents for DSO-X 2014A



























































































































































































































































































































































































Reviews:

No comments

Related manuals for DSO-X 2014A

FagronLab FG User Manual preview
FG
Brand: FagronLab Pages: 16
Raytech TR-1 Instruction Manual preview
TR-1
Brand: Raytech Pages: 21
Teac LX Series Specifications preview
LX Series
Brand: Teac Pages: 2
laerdal HEARTSTART Quick Start Manual preview
HEARTSTART
Brand: laerdal Pages: 2
Abbott CentriMag Quick Reference Manual preview
CentriMag
Brand: Abbott Pages: 2
Abbott FreeStyle Libre Software Update preview
FreeStyle Libre
Brand: Abbott Pages: 3
abc PHASER Operation And Maintenance Manual preview
PHASER
Brand: abc Pages: 8
Keller HPX Operating Instructions Manual preview
HPX
Brand: Keller Pages: 12
MacDon D50 Installation Manual preview
D50
Brand: MacDon Pages: 49
MacDon D50 Unloading And Assembly Instructions preview
D50
Brand: MacDon Pages: 49
MacDon D50 Quick Start Manual preview
D50
Brand: MacDon Pages: 4
RainPoint ITV105 User Manual preview
ITV105
Brand: RainPoint Pages: 40
FARM-MAXX FTL Series Operator'S Manual preview
FTL Series
Brand: FARM-MAXX Pages: 35
Daekyung DTR-300N Operation Manual preview
DTR-300N
Brand: Daekyung Pages: 15
Wacker Neuson RS 800A Operator'S Manual preview
RS 800A
Brand: Wacker Neuson Pages: 42
KERR 815-1655 Instructions For Use Manual preview
815-1655
Brand: KERR Pages: 32
ebm-papst R1G225-AG15-11 Operating Instructions Manual preview
R1G225-AG15-11
Brand: ebm-papst Pages: 10
Eaton CEAG Exit Cube 33822 LED CGLine+ Mounting And Operating Instructions preview
CEAG Exit Cube 33822 LED CGLine+
Brand: Eaton Pages: 20

Brands by name

Popular brands

Load more brands