Keysight Technologies DSO-X 2014A User Manual Download Page 62

Page: 62 / 378

Keysight InfiniiVision 2000 X-Series Oscilloscopes User's Guide

Vertical Controls

The ground level of the signal for each displayed analog channel is identified by
the position of the

icon at the far-left side of the display.

To turn waveforms on or off (channel or math)

Press an analog channel key turn the channel on or off (and to display the

channel's menu).

When a channel is on, its key is illuminated.

Channel,
Volts/div

Channel 1
ground
level

Trigger
source

Trigger level
or threshold

Channel 2
ground
level

NOTE

Turning channels off

You must be viewing the menu for a channel before you can turn it off. For example, if channel

1 and channel 2 are turned on and the menu for channel 2 is being displayed, to turn channel

1 off, press

[1]

to display the channel 1 menu; then, press

[1]

again to turn channel 1 off.

Summary of Contents for DSO-X 2014A



























































































































































































































































































































































































Search results

Summary of Contents for DSO-X 2014A

Reviews:

Related manuals for DSO-X 2014A

Brands by name

Popular brands

Keysight Technologies DSO-X 2014A, User Manual

Search results

Summary of Contents for DSO-X 2014A

Reviews:

Related manuals for DSO-X 2014A

Brands by name

Popular brands