manualshive.com logo in svg

Keysight Technologies DSO-X 2014A, User Manual

The Keysight Technologies DSO-X 2014A is a high-performance oscilloscope designed for accurate measurements and analysis. To make the most of its features, be sure to download the free User Manual from manualshive.com. This manual provides detailed instructions on how to operate and maximize the capabilities of this powerful tool.

Share
Download
background image

295

Keysight InfiniiVision 2000 X-Series Oscilloscopes 

User's Guide

 

21 Web Interface

Accessing the Web Interface / 296
Browser Web Control / 297
Save/Recall / 300
Get Image / 302
Identification Function / 303
Instrument Utilities / 303
Setting a Password / 305

When the Keysight InfiniiVision X-Series oscilloscopes have the DSOXLAN 

LAN/VGA option module installed, you can access the oscilloscope's built-in web 

server using a web browser. The oscilloscope's web interface lets you:
• View information about the oscilloscope like its model number, serial number, 

host name, IP address, and VISA (address) connect string.

• Control the oscilloscope using the Remote Front Panel.
• Send SCPI (Standard Commands for Programmable Instrumentation) remote 

programming commands via the SCPI Commands applet window.

• Save setups, screen images, waveform data, and mask files.
• Recall setup files, reference waveform data files, or mask files.
• Get screen images and save or print them from the browser.
• Activate the Identification function to identify a particular instrument by 

causing a message to be displayed or a front panel light to blink.

• View installed options, view firmware versions and install firmware upgrade 

files, and view calibration status (via the Instrument Utilities page).

• View and modify the oscilloscope's network configuration.

Summary of Contents for DSO-X 2014A



























































































































































































































































































































































































Reviews:

No comments

Related manuals for DSO-X 2014A

Makerfire N10 Instructions Manual preview
N10
Brand: Makerfire Pages: 10
KaVo 4040 Operating, Maintenance And Assembly Instructions preview
4040
Brand: KaVo Pages: 16
MacDon R216 Quick Card preview
R216
Brand: MacDon Pages: 2
MacDon R216 Operator'S Manual preview
R216
Brand: MacDon Pages: 214
MacDon R216 Installation Instructions Manual preview
R216
Brand: MacDon Pages: 32
UFO Vega Product User Manual preview
Vega
Brand: UFO Pages: 16
NEILPRYDE X1 Manual preview
X1
Brand: NEILPRYDE Pages: 53
JAC PRO+ Translation Of Original User Instructions preview
PRO+
Brand: JAC Pages: 103
3Disc Heron IOS Quick Start Manual preview
Heron IOS
Brand: 3Disc Pages: 12
idiag P100 Quick Reference Manual preview
P100
Brand: idiag Pages: 12
AcceleDent aura Frequently Asked Questions preview
aura
Brand: AcceleDent Pages: 3
Zero 88 Solution Quick Start Manual preview
Solution
Brand: Zero 88 Pages: 32
Eastern Jungle Gym CLASSIC Owner'S Instruction Manual preview
CLASSIC
Brand: Eastern Jungle Gym Pages: 17
Vahle VCL Series Translation Of The Original Operating Instructions preview
VCL Series
Brand: Vahle Pages: 96
Danfoss iSave 21 User Manual preview
iSave 21
Brand: Danfoss Pages: 106
Unitary products group PS8 Installation Manual preview
PS8
Brand: Unitary products group Pages: 28
Yamaha TG77 Owner'S Manual preview
TG77
Brand: Yamaha Pages: 139
Yamaha TG77 Midi Data Format preview
TG77
Brand: Yamaha Pages: 19

Brands by name

Popular brands

Load more brands