manualshive.com logo in svg

Keysight Technologies DSO-X 2014A, User Manual

The Keysight Technologies DSO-X 2014A is a high-performance oscilloscope designed for accurate measurements and analysis. To make the most of its features, be sure to download the free User Manual from manualshive.com. This manual provides detailed instructions on how to operate and maximize the capabilities of this powerful tool.

Share
Download
background image

28

Keysight InfiniiVision 2000 X-Series Oscilloscopes User's Guide

1

Getting Started

 

When using the oscilloscope in a bench-top setting, provide at least 2" clearance 

at the sides and 4" (100 mm) clearance above and behind the oscilloscope for 

proper cooling.

To power-on the

oscilloscope

1

Connect the power cord to the rear of the oscilloscope, then to a suitable AC 

voltage source. Route the power cord so the oscilloscope's feet and legs do not 

pinch the cord.

Install the instrument so that the detachable power cord is readily identifiable 

and is easily reached by the operator. The detachable power cord is the 

instrument disconnecting device. It disconnects the mains circuits from the 

mains supply before other parts of the instrument. The front panel switch is only 

a standby switch and is not a LINE switch. Alternatively, an externally installed 

switch or circuit breaker (which is readily identifiable and is easily reached by 

the operator) may be used as a disconnecting device.

2

The oscilloscope automatically adjusts for input line voltages in the range 100 

to 240 VAC. The line cord provided is matched to the country of origin.

3

Press the power switch.

The power switch is located on the lower left corner of the front panel. The 

oscilloscope will perform a self-test and will be operational in a few seconds.

Connect Probes to the Oscilloscope

1

Connect the oscilloscope probe to an oscilloscope channel BNC connector.

CAUTION

 Use 

only

 the power cord that came with the oscilloscope

The power cord provided is matched to the country of origin of the order.

WARNING

Always use a grounded power cord. Do not defeat the power cord ground.

Summary of Contents for DSO-X 2014A



























































































































































































































































































































































































Reviews:

No comments

Related manuals for DSO-X 2014A

Campden instruments 7600 Series Instruction Manual preview
7600 Series
Brand: Campden instruments Pages: 8
ParaBody 810 Assembly Instruction Sheet preview
810
Brand: ParaBody Pages: 4
MADRIX NEO Quick Start Manual & Technical Manual preview
NEO
Brand: MADRIX Pages: 12
Narcotrend Compact M Operating Instructions Manual preview
Compact M
Brand: Narcotrend Pages: 47
TATU PT Operator'S Manual preview
PT
Brand: TATU Pages: 30
Rane HC6S Operator'S Manual preview
HC6S
Brand: Rane Pages: 4
Sabio 2010D Operation Manual preview
2010D
Brand: Sabio Pages: 182
Haas TR Series Installation Manual preview
TR Series
Brand: Haas Pages: 12
SaMASZ Spin Operator'S Manual preview
Spin
Brand: SaMASZ Pages: 25
Yamaha MCX-C15 - MusicCAST Network Audio Player Owner'S Manual preview
MCX-C15 - MusicCAST Network Audio Player
Brand: Yamaha Pages: 65
Yamaha Audiogram6 Manuel Du Propriétaire preview
Audiogram6
Brand: Yamaha Pages: 24
Vuly Ring Swing Manual preview
Ring Swing
Brand: Vuly Pages: 4
REED vc04 Instruction Manual preview
vc04
Brand: REED Pages: 12
SHOWTEC Spectral M950 Q4 Tour Manual preview
Spectral M950 Q4 Tour
Brand: SHOWTEC Pages: 24
Ibiza 16-2043 Manual preview
16-2043
Brand: Ibiza Pages: 20
Datavideo TBC-6000 Instruction Manual preview
TBC-6000
Brand: Datavideo Pages: 4
TaiShan TQ2550/A Installation preview
TQ2550/A
Brand: TaiShan Pages: 5
Garland KLS 2000 Operating Instructions Manual preview
KLS 2000
Brand: Garland Pages: 24

Brands by name

Popular brands

Load more brands