Keysight Technologies DSO-X 2014A User Manual Download Page 120

Page: 120 / 378

120

Keysight InfiniiVision 2000 X-Series Oscilloscopes User's Guide

Serial Decode

To determine whether these licenses are installed on your oscilloscope, see

"To

display oscilloscope information"

on page 290.

To order serial decode licenses, go to

www.keysight.com

and search for the

product number (see

"Licensed Options Available"

on page 312) or contact your

local Keysight Technologies representative (see

www.keysight.com/find/contactus).

Lister

Lister is a powerful tool for investigating protocol failures. You can use Lister to

view large amounts of packet level serial data in a tabular format, including time

tags and specific decoded values. After pressing the

[Single]

key, you can press the

Scroll Lister

softkey and then rotate the Entry knob to select an event and press the

Zoom to Selection

softkey to jump to the event.

To use the Lister:

Set up trigger and decode on the serial data signals to be analyzed.

Press

[Serial] > Lister

Press

Display

; then, turn the Entry knob to select the serial slot (

Serial 1

) on

which the serial bus signals are being decoded.

I2C (Inter-IC) and SPI (Serial Peripheral

Interface) serial buses.

•

•

UART (Universal Asynchronous

Receiver/Transmitter) protocols including

RS232 (Recommended Standard 232).

•

"UART/RS232 Serial Decode"

page 365.

Licensed Serial Decode

See:

Summary of Contents for DSO-X 2014A



























































































































































































































































































































































































Search results

Summary of Contents for DSO-X 2014A

Reviews:

Related manuals for DSO-X 2014A

Brands by name

Popular brands

Keysight Technologies DSO-X 2014A, User Manual

Search results

Summary of Contents for DSO-X 2014A

Reviews:

Related manuals for DSO-X 2014A

Brands by name

Popular brands