Keysight Technologies DSO-X 2014A User Manual Download Page 217

Page: 217 / 378

Measurements

Keysight InfiniiVision 2000 X-Series Oscilloscopes User's Guide

217

+ Width

+ Width

is the time from the middle threshold of the rising edge to the middle

threshold of the next falling edge. The X cursors show the pulse being measured.

The Y cursor shows the middle threshold point.

– Width

– Width

is the time from the middle threshold of the falling edge to the middle

threshold of the next rising edge. The X cursors show the pulse being measured.

The Y cursor shows the middle threshold point.

Bit Rate

The bit rate measurement measures all positive and negative pulse widths on the

waveform, takes the minimum value found of either width type and inverts that

minimum width to give a value in Hertz.

Figure 47

Isolating an event for Frequency measurement

Summary of Contents for DSO-X 2014A



























































































































































































































































































































































































Search results

Summary of Contents for DSO-X 2014A

Reviews:

Related manuals for DSO-X 2014A

Brands by name

Popular brands

Keysight Technologies DSO-X 2014A, User Manual

Search results

Summary of Contents for DSO-X 2014A

Reviews:

Related manuals for DSO-X 2014A

Brands by name

Popular brands