Keysight Technologies DSO-X 2014A User Manual Download Page 147

Page: 147 / 378

Triggers

Keysight InfiniiVision 2000 X-Series Oscilloscopes User's Guide

147

•

sets the pattern to zero (low) on the selected channel. A low is a voltage

level that is less than the channel's trigger level or threshold level.

•

sets the pattern to 1 (high) on the selected channel. A high is a voltage

level that is greater than the channel's trigger level or threshold level.

•

sets the pattern to don't care on the selected channel. Any channel set to

don't care is ignored and is not used as part of the pattern. However, if all

channels in the pattern are set to don't care, the oscilloscope will not trigger.

•

The rising edge ( ) or falling edge ( ) softkey sets the pattern to an edge

on the selected channel. Only one rising or falling edge can be specified in

the pattern. When an edge is specified, the oscilloscope will trigger at the

edge specified if the pattern set for the other channels is true.

If no edge is specified, the oscilloscope will trigger on the last edge that

makes the pattern true.

NOTE

Specifying an Edge in a Pattern

You are allowed to specify only one rising or falling edge term in the pattern. If you define an

edge term, then select a different channel in the pattern and define another edge term, the

previous edge definition is changed to a don't care.

Summary of Contents for DSO-X 2014A



























































































































































































































































































































































































Search results

Summary of Contents for DSO-X 2014A

Reviews:

Related manuals for DSO-X 2014A

Brands by name

Popular brands

Keysight Technologies DSO-X 2014A, User Manual

Search results

Summary of Contents for DSO-X 2014A

Reviews:

Related manuals for DSO-X 2014A

Brands by name

Popular brands