![background image](http://html1.mh-extra.com/html/karcher/b-260-ri/b-260-ri_manual_3574742022.webp)
22
English
Adjusting the suction bar
The suction bar only needs to be readjusted in special
cases. The factory setting is suitable for most applica-
tions.
Adjusting the inclination of the suction bar
The inclination must be adjusted so that the suction lips
of the suction bar make even contact with the floor over
the entire length of the suction bar.
1. Park the device on a surface without a slope.
2. Select the "Suction" program.
3. Drive the device a small distance forwards.
The suction bar is lowered.
4. Read the spirit level.
Illustration N
1
Screw
2
Nut
3
Spirit level
5. Release the M 12 nut while holding the
M 10 hexagon head screw with an open-end
wrench.
6. Adjust the screw so that the spirit level indicator is
between the two lines.
7. Tighten the M 12 nut while holding the
M 10 hexagon head screw with an open-end
wrench.
8. To check the new setting, move the device forward
a short distance in suction mode with the suction bar
lowered and observe the spirit level. Repeat the ad-
justment process if necessary.
Sweeping (Combo variant only)
The sweeping mechanism picks up loose dirt before
cleaning the floor.
몇
WARNING
Moving parts
Risk of injury
Note that the suction turbine, side brushes and filter de-
dusting run on after switching off.
ATTENTION
Improper use of the device when sweeping
Risk of damage to the sweeping mechanism.
Do not sweep up packing tape, wires or similar.
Only drive over steps up to a maximum of 2 cm.
Sweep only dry surfaces to prevent clogging and con-
tamination of the dust filter.
1. Switch on the "Sweeping" switch.
The sweeping mechanism is activated.
Coarse dirt flap
The coarse dirt flap can be lifted to sweep up larger ob-
jects (up to approx. 6 cm high).
DANGER
Risk of injury from waste!
Waste can be thrown out when the coarse dirt flap is
opened.
Only lift the coarse dirt flap when there are no persons
in the vicinity.
Note
The sweeping effect and dust suction deteriorate when
the coarse dirt flap is raised. Only lift the coarse dirt flap
when necessary.
1. Operate the pedal to raise the coarse dirt flap.
Ending sweeping
1. Set the "Sweeping" switch to "0".
The sweeping mechanism is deactivated. After the
sweeping operation is finished, the dust filter is cleaned
for approx. 15 seconds.
Side scrubbing deck (option)
The side scrubbing deck makes working close to the
edge easier.
Illustration AS
1
Extending/retracting the side scrubbing deck
2
Switching the side scrubbing deck on/off
1. Press the "Switch side scrubbing deck on/off"
switch.
The side scrubbing deck is switched on/off.
2. Press the "Retract/extend side scrubbing deck"
switch.
The side scrubbing deck is retracted/extended.
Finishing operation
Finishing cleaning
1. Set the program selection switch to Drive.
2. Continue moving a short distance.
The residual water is vacuumed up.
3. Turn the program selection switch to position "0".
4. Remove the Intelligent Key.
5. Charge the battery if necessary.
Emptying the waste water tank
몇
WARNING
Improper disposal of waste water
Environmental pollution
Observe the local waste water treatment regulations.
Note
The suction turbine switches off and the display shows
"Waste water tank full" when the waste water tank is full.
1. Remove the waste water drain hose from the holder.
2. Lower the end of the hose over the disposal facility.
Illustration P
3. Drain the waste water by opening the cap on the
drain hose.
The water flow can be reduced by squeezing or
twisting the dosing device.
4. Remove the spray gun from the holder.
5. Set the program selection switch to Transport.
6. Select "Tank rinsing" on the display.
a Press the Info button.
b Select the "Tank rinsing" menu.
7. Open the stop valve on the back of the waste water
tank.
8. Rinse the waste water tank with the spray nozzle.
9. Hang the spray nozzle in the holder.
10. Close the drain hose cover.
11. Press the waste water hose into the support on the
device.
12. Close the stop valve at the back of the waste water
tank.
13. Select "Tank rinsing" on the display.
Emptying the waste container
Note
The waste container can only be removed via the driv-
er's side and is only present on R cleaning heads.
1. Pull the tab.
2. Pivot open the squeegee blade holder.
3. Remove the waste container.
Illustration AI
1
Tab
2
Squeegee blade holder
3
Waste container
4. Empty the waste containers.
5. Fit the waste container.
Note
The waste container must latch into place.
6. Pivot the squeegee blade holder closed.
Draining fresh water
ATTENTION
Cleaning solution in the fresh water tank
Damage to fresh water tank, valves and seals
Never leave the cleaning solution in the fresh water tank
at the end of operation.
1. Remove the fresh water drain hose from the holder
and lower it over a suitable collecting device.
2. Drain the cleaning solution.
3. Remove the fresh water tank cap.
4. Rinse the fresh water tank with clear water (maxi-
mum 60 °C).
Shutting down the device
1. Turn the key-operated switch to "OFF".
2. Remove the Intelligent Key.
3. Secure the device against rolling away.
4. Charge the battery if necessary.
Grey Intelligent Key
The grey Intelligent Key grants the supervisory staff ex-
tended authorizations and setting options.
1. Insert the Intelligent Key.
2. Select the desired function by turning the info but-
ton.
Transport journey
1. Set the program selector switch to "Transport trav-
el".
2. Press the Info button.
The following settings can be made in the Transport
travel menu:
●
Resetting the maintenance counter
●
Resetting the day counter
●
Key management
●
Choosing the brush shape
●
After-running time
●
Standard setting
●
Setting the language
●
Switch menu
●
Travel speed
●
Factory setting
●
Activating the manual tank rinsing gun
Resetting the maintenance counter
If maintenance work shown in the display has been car-
ried out, the corresponding maintenance counter must
then be reset.
1. Turn the Info button until "Maintenance counter" is
displayed.
2. Press the Info button.
The counter readings are displayed.
3. Turn the info button until the counter to be cleared is
highlighted.
4. Press the Info button.
5. Select "Yes" by turning the Info button.
6. Press the Info button.
The counter is cleared.
Note
The service counter can only be reset by Customer Ser-
vice staff.
The service counter shows the time until the next ser-
vice due by Customer Service.
Resetting the counter
1. Turn the Info button until "Counter" is displayed.
This menu shows the total operating hours and the
day counter.
Delete the day counter:
2. Press the Info button.
The "Delete counter" menu is displayed.
3. Turn the Info button until "Day counter" is highlight-
ed.
4. Press the Info button.
Key management
The authorizations are assigned for each yellow Intelli-
gent Key used and the language of the display is set for
this Intelligent Key in the "Key menu" menu item.
1. Insert the grey Intelligent Key.
2. Turn the info button until the "Key menu" menu item
appears on the display.
3. Press the Info button.
4. Remove the grey Intelligent Key and insert the yel-
low or white Intelligent Key to be personalized.
5. Select the menu item to be changed by turning the
info button.
6. Press the Info button.
7. Select the setting of the menu item by turning the in-
fo button.
8. Confirm the setting by pressing the menu item.
9. Select the next menu item to be changed by turning
the info button.
10. After all settings have been made, call up the
"Save?" menu by turning the info button.
11. Press the Info button.
The authorizations are saved.
The "Continue key menu" display appears.
●
Yes: Program another Intelligent Key
●
No: Exit the key menu
12. Press the Info button.
Choosing the brush shape
This function is required when changing the cleaning
head.
1. Turn the info button until the "Brush head" menu
item appears on the display.
2. Press the Info button.
3. Turn the info button until the desired brush shape is
highlighted.
4. Press the Info button.
5. To change the cleaning head, move the lifting drive
by turning the info button:
"Up": Lifting
"Down": Lowering
"OFF": Stopping
6. Turn the info button until the "OFF" menu item is dis-
played.
7. Press the Info button.
The menu is exited.
The controller performs a restart.
After-running time
1. Turn the info button until the "After-running time"
menu item appears on the display.
2. Press the Info button.
3. Turn the info button until the desired function is high-
lighted.
4. Press the Info button.
5. Turn the info button until the desired after-running
time is displayed.
6. Press the Info button.
Standard setting
1. Turn the info button until the "Standard setting"
menu item appears on the display.
2. Press the Info button.
3. Turn the info button until the desired accessory is
highlighted.
4. Press the info button to confirm ON/OFF.
5. Press the info button to exit the menu.
Summary of Contents for B 260 RI
