![background image](http://html1.mh-extra.com/html/karcher/b-260-ri/b-260-ri_manual_3574742021.webp)
English
21
5. Release the accelerator pedal.
The brake must audibly lock.
If the parking brake does not lock, shut down the device,
secure it against uncontrolled rolling and contact the
customer service.
Checking the foot brake
DANGER
Danger of accident due to defective foot brake!
The device may roll uncontrollably if the foot brake is not
working properly.
Check the function of the parking brake on level ground
before each use.
1. Switch the device on.
2. Set the travel direction switch to "Forward".
3. Set the program switch to transport travel.
4. Press the accelerator pedal.
5. While driving, take your foot off the accelerator and
apply the foot brake.
Device must decelerate noticeably.
If this is not the case, shut down the device and call
Customer Service.
Driving
DANGER
Lack of braking
Danger of accident
Before using the device, it is essential to check the func-
tion of the parking brake. Never use the device if the
parking brake does not work.
DANGER
No braking effect during operation
If the device no longer has any braking effect during op-
eration, proceed as follows:
If the device does not come to a standstill on a ramp with
a gradient of more than 2% when you release the accel-
erator pedal, for safety reasons you may only set the
safety switch to position "0" if you have checked the cor-
rect mechanical function of the parking brake before
starting up the device.
After reaching a standstill, put the device out of opera-
tion and call Customer Service.
Observe the maintenance instructions for brakes.
DANGER
Careless driving
Danger of tipping over
Only drive on slopes in the travel direction up to a max-
imum of 15% (RI variant) and 10% (RI Combo variant).
Slopes transverse to the travel direction up to a maxi-
mum of 15%.
Do not turn up or down gradients.
Drive slowly in corners and on wet ground.
Only drive the device on stable ground.
Pivoting sweeping mechanism on the Combo vari-
ant
Increased risk of accidents
Be especially careful when reversing.
Take the pivoting of the sweeping mechanism into ac-
count when steering.
Note
The travel direction can be changed while driving. This
allows very dull spots to be polished by moving back
and forth several times.
1. Assume a seated position.
2. Insert the Intelligent Key.
3. Set the program selection switch to "Transport trav-
el".
4. Set the travel direction using the travel direction but-
ton on the control panel.
5. Specify the travel speed by pressing the accelerator
pedal.
6. Release the accelerator pedal.
The device stops.
The driving motor is switched off in the event of an over-
load. A fault message appears on the display. If the con-
troller overheats, the affected power unit is switched off.
7. Allow the device to cool down for at least 15 min-
utes.
8. Set the program switch to "0", wait briefly and set to
the desired program.
Adjusting the driver's seat
Illustration J
1
3-stage weight adjustment 60-120 Kg
2
Backrest tilt adjustment 3° forward and 13° back-
ward
3
Seat length adjustment
1. Operate the seat adjustment lever.
2. Move the seat to the desired position.
3. Release the seat adjustment lever.
Adjusting the steering wheel
1. Release the wing nuts for adjusting the steering
wheel.
2. Position the steering wheel.
3. Tighten the wing nuts.
Checking the lint filter
ATTENTION
Damage to the suction turbine!
Operating without a lint filter can damage the suction
turbine.
Do not operate the device without the lint filter.
1. Check the following lint filter aspects before starting
up the device:
Is it present?
Is it in a usable condition?
Is it installed correctly?
Illustration AL
1
Lint filter
2. Replace a damaged lint filter.
Pushing the device
1. Release the parking brake by pulling the lever away.
Note
The lever must be pulled all the way.
DANGER
Risk of injury from rolling device!
The parking brake can only be released while bent over
and staying in the danger zone.
Use an object to hold the lever in a permanently pulled
state and move away from the danger zone immediately
after opening the parking brake.
Illustration AK
1
Parking brake lever
2. Push the device.
3. Close the parking brake again by releasing the le-
ver.
Filling with fresh water
Filling fresh water
1. Open the fresh water tank cap.
2. Secure the fresh water hose with the clamp.
3. Fill fresh water (max. 60 °C) to approx. 5 cm below
the filler funnel.
Note
Fill the fresh water tank completely before initial startup
in order to vent the water pipe system.
4. ´Remove the fresh water tank cap.
Filling fresh water with the fresh water tank
automatic filling system (option)
Note
We recommend that you use a hose with an Aquastop
coupling on the device side. This minimises the splash-
ing out of water when disconnecting after the filling pro-
cess.
1. Connect the water hose to the automatic filling sys-
tem.
2. Open the water supply (max. 60 °C, max. 10 bar).
3. Monitor the filling process, the automatic filling sys-
tem interrupts the water supply when the fresh water
tank is full.
4. Close the water inlet.
5. Remove the water hose.
Filling with detergent
Notes on detergents
몇
WARNING
Unsuitable detergents
Health risk, damage to the device
Use only recommended detergents. The operator car-
ries all increased risks relating to operational safety and
increased risk of accidents if using other detergents.
Use only detergents free of solvents, salt and hydrofluo-
ric acid.
Adhere to the safety instructions stated on the detergent
packaging.
Note
Do not use heavily foaming detergent.
Recommended detergents
Filling the detergent into the fresh water tank
Note
First fill water into the detergent tank, then add the ap-
propriate dosage of detergent to the tank. If the deter-
gent is poured in first, this can lead to strong foaming.
ATTENTION
Danger of clogging
When adding detergent to the fresh water tank, the de-
tergent can dry out and disrupt the function of the dosing
device.
Rinse the device with clear water after adding the deter-
gent to the fresh water tank: Select a cleaning program
with water application, set the water quantity to the high-
est value, set the detergent dosage to "0".
Filling detergent with a dosing device
(option)
Detergent is added to the fresh water on the way to the
cleaning head by a dosing device.
Note
A maximum of 3% detergent can be added with the dos-
ing device. If the dosage is higher, the detergent must
be added to the fresh water tank.
ATTENTION
Danger of clogging
When adding detergent to the fresh water tank, the de-
tergent can dry out and disrupt the function of the dosing
device.
Rinse the device with clear water after adding the deter-
gent to the fresh water tank: Select a cleaning program
with water application, set the water quantity to the high-
est value, set the detergent dosage to 0.
1. Place the canister with the detergent in the deter-
gent tray behind the seat.
2. Unscrew the canister cap.
3. Insert the detergent suction lance of the dosing de-
vice into the canister.
Note
●
The device has a fresh water level indicator on the
display. Detergent dosing is also stopped when the
fresh water tank is empty. The cleaning head contin-
ues to work without supply of liquid.
●
Detergent addition is also stopped when the deter-
gent canister is empty. A message symbol appears
on the display. Only fresh water is fed to the cleaning
head.
Adjusting parameters (yellow Intelligent key)
The parameters for the various cleaning programs are
preset in the device.
Individual parameters can be changed depending on
the authorization of the yellow Intelligent Key.
The modified parameters only remain in effect until a dif-
ferent cleaning program is selected with the program
switch.
A grey Intelligent Key must be used for making adjust-
ments if parameters are to be changed permanently.
This setting procedure is described in the section "Grey
Intelligent Key".
Note
R cleaning head only: Almost all displayed texts regard-
ing parameter settings are self-explanatory. If you need
more detailed information about the parameters, please
contact the Customer Service.
●
Fine Clean: Low brush speed for removing grey film
from fine stone.
●
Whisper Clean: Medium brush speed for mainte-
nance cleaning with reduced noise level.
●
Power Clean: High brush speed for polishing, crys-
tallizing and sweeping.
1. Set the program switch to the desired cleaning pro-
gram.
2. Press the Info button.
3. Turn the Info button until the desired parameter is
displayed.
4. Press the Info button.
The adjusted value flashes.
5. Set the desired value by turning the Info button.
6. Confirm the changed setting by pressing the Info
button or wait until the set value is automatically ac-
cepted after 10 seconds.
Application
Detergent
Maintenance cleaning of all water-
resistant floors
CA 50 C
RM 756
Maintenance cleaning with care
components
RM 746
RM 780
Maintenance cleaning and basic
cleaning of industrial floors
RM 69
Maintenance cleaning of glossy cov-
erings
RM 755
Maintenance cleaning and basic
cleaning of fine stone tiles
RM 753
Maintenance cleaning and basic
cleaning of acid-resistant coverings
RM 751
Cleaning and disinfection
RM 732
Basic cleaning of all alkali-resistant
floor coverings
RM 752
Basic cleaning and de-coating of al-
kali-sensitive floors
RM 754
Application
Detergent
Summary of Contents for B 260 RI
