JDS Uniphase CellAdvisor JD780A Series User Manual Download Page 559

Page: 559 / 592

JD780A Series Analyzers

Using Power Meter

559

Making a power measurement

Procedure

After setting the parameters, read the absolute measurement value in dBm on the screen.

Figure 296

is an example of the measurement screen. To view a relative power, see “Reading a

relative power

” on page 559.

To view the result in mW, complete the following steps:

Press the

AMP/SCALE

hard key.

Press the

Units

soft key, and then select

To set a threshold and view the result with Pass/Fail indication, complete the following steps:

Press the

LIMIT

hot key.

Toggle the

Threshold

soft key between

and

Off

to enable or disable the Pass/Fail

indication.

Press the

Threshold

soft key, and then enter a value.

Press the

dBm

unit soft key.

Toggle the

Alarm

soft key between

and

Off

to enable or disable alarming.

Optional

. Go to

SAVE/LOAD

> Save

, and then select the save option from the choices available

for your measurement mode. See

“Using save” on page 31 for more information.

Figure 296

optical power measurement

NOTE

If the Wavelength is set to Auto, it displays

“Auto” for the modulation frequency. It it is set

to Manual, the instrument displays a detected modulation frequency.

Reading a relative power

To view a relative power in dB, you can set a reference value automatically or manually.

Procedure

Press the

AMP/SCALE

hard key.

Toggle the

Display

soft key and select

Relative

Summary of Contents for CellAdvisor JD780A Series

















































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CellAdvisor JD780A Series

Reviews:

Brands by name

Popular brands

JDS Uniphase CellAdvisor JD780A Series, User Manual

Search results

Summary of Contents for CellAdvisor JD780A Series

Reviews:

Brands by name

Popular brands