manualshive.com logo in svg

JDS Uniphase CellAdvisor JD780A Series, User Manual

Share
Download
JDS Uniphase CellAdvisor JD780A Series User Manual Download Page 289

JD780A Series Analyzers

 

 

Using LTE 

– TDD Signal Analyzer

 

289

 

Figure 132

  Data channel measurement with LTE - TDD signal analyzer (MBMS On) 

 

 

 

NOTE

 

You can use the 

LIMIT

 hot key to analyze your measurements with the user-definable 

limit and Pass/Fail indication. See 

“Setting limit for modulation tests” on page 300 for 

more information. 

 

Using marker 

You can use the 

MARKER

 hard key to place a marker on a resource block and display the IQ diagram 

for the selected resource block. 
 

Procedure

 

1. 

Press the 

MARKER

 hard key. 

2. 

Press the 

RB

 

Number

 soft key to select the resource block to be marked. 

3. 

Enter the resource block number by using the numeric keys. 

4. 

Press the 

Enter

 soft key. 

The marker appears on the selected resource block. 

5. 

Toggle the 

Marker View

 soft key between 

On

 and 

Off

 to display or dismiss the result of the 

selected resource block. 

 

Control channel 

The Control Channel measures the constellation for the specified control channel as well as 
modulation accuracy of the control channel at the specified subframe. 
 

Setting measure setup 

After configuring test parameters as described in the 

“Configuring test parameters” on page 265, you 

can continue your measurement. The measurement settings can be saved and recalled as a file. You 
can also use JDViewer, PC application software to configure a measure setup, save as a file, and load 
the file on to the instrument. 
 

Summary of Contents for CellAdvisor JD780A Series

















































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands