JDS Uniphase CellAdvisor JD780A Series User Manual Download Page 299

Page: 299 / 592

JD780A Series Analyzers

Using LTE

– TDD Signal Analyzer

299

Measurement example

Figure 138

Data allocation map measurement with LTE - TDD signal analyzer

Figure 139

Data allocation map measurement with LTE - TDD signal analyzer (MBMS On)

NOTE

You can use the

LIMIT

hot key to analyze your measurements with the user-definable

limit and Pass/Fail indication. See

“Setting limit for modulation tests” on page 300 for

more information.

Setting display

You can use the

TRACE/DISPLAY

hard key to change the display mode to PDSCH, PMCH, or both.

Procedure

Press the

TRACE/DISPLAY

hard key.

Summary of Contents for CellAdvisor JD780A Series

















































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CellAdvisor JD780A Series

Reviews:

Brands by name

Popular brands

JDS Uniphase CellAdvisor JD780A Series, User Manual

Search results

Summary of Contents for CellAdvisor JD780A Series

Reviews:

Brands by name

Popular brands