JDS Uniphase CellAdvisor JD780A Series User Manual Download Page 420

Page: 420 / 592

JD780A Series Analyzers

420

Using TD-SCDMA Signal Analyzer

connected and locked.

GPS

(yellow)

The yellow GPS antenna icon indicates that a GPS antenna is
connected and locking is in progress.

GPS

(grey)

The grey GPS antenna icon indicates that a GPS antenna is not
connected, failed, or unable to be locked.

Conducting spectrum measurements

Setting measure setup

After configuring test parameters as described in the

“Configuring test parameters” on page 415, you

can continue your measurement.

Procedure

Press the

MEASURE SETUP

hot key.

Press the

Slot Number

soft key, and then select the time slot number to be displayed:

TS0

TS1

TS2

TS3

TS4

TS5

, or

TS6

Optional

. To set the delay, complete the following steps:

Press the

Delay

soft key to set the amount of delay in µs.

Enter a value by using the numeric keys. You can also use the rotary knob.

Press the

µs

soft key.

NOTE

The Delay setting is used only when there is a time offset in the signals to be measured.

Your measurement result is displayed on the screen as like the following example, Figure 205.

Figure 205

Spectrum measurement screen with TD-SCDMA signal analyzer

Summary of Contents for CellAdvisor JD780A Series

















































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CellAdvisor JD780A Series

Reviews:

Brands by name

Popular brands

JDS Uniphase CellAdvisor JD780A Series, User Manual

Search results

Summary of Contents for CellAdvisor JD780A Series

Reviews:

Brands by name

Popular brands