ITT Goulds Pumps CV 3196 i-FRAME Installation, Operation And Maintenance Manual Download Page 92

Page: 92 / 178

NOTICE:

Use force only on the inner race when pressing bearings from the shaft. Failure to do so may
result in equipment damage.

NOTICE:

Do not reuse bearings if removed from shaft. Doing so may result in equipment damage. Re-
place the bearings before reassembly.

168

361A

122

112

382

136

Figure 71: Outboard bearing removal

6.4.15.2 Disassemble the power end (STi and MTi with duplex bearings)

Remove the clamp screws (370C) and back off the jam nuts (423).

Tighten the jack screws (370D) evenly to move the bearing housing (134) out of the bearing frame
(228A).

Remove the shaft assembly from the bearing frame (228A).

228A

134

370D

423

370C

Figure 72: Shaft assembly removal

Remove the jack screws (370D) with the nuts (423).

6.4 Disassembly

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

Summary of Contents for Goulds Pumps CV 3196 i-FRAME



















































































































































































Search results

Summary of Contents for Goulds Pumps CV 3196 i-FRAME

Reviews:

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brands by name

Popular brands

ITT Goulds Pumps CV 3196 i-FRAME, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Goulds Pumps CV 3196 i-FRAME

Reviews:

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brands by name

Popular brands