ITT Goulds Pumps CV 3196 i-FRAME Installation, Operation And Maintenance Manual Download Page 111 | Manualshive

Page: 111 / 178

background image

STi millimeters | in-
ches

MTi millimeters | in-
ches

LTi millimeters | inches XLT-i, i-17 millimeters |

inches

Outboard

71.986 | 2.8341

99.985 | 3.9364

109.985 | 4.3301

139.982 | 5.5111

6.6 Reassembly

6.6.1 Assemble the rotating element and the bearing frame (STi and MTi)

CAUTION:

Risk of physical injury from hot bearings. Wear insulated gloves when using a bearing heater.

NOTICE:

Ensure that the pipe threads are clean. Apply thread sealant to the plugs and fittings. Failure to
do so may result in oil leaks and equipment damage.

NOTICE:

There are several methods used to install bearings. The recommended method is to use an
induction heater that heats as well as demagnetizes the bearings. Failure to use this method
may result in equipment damage.

1.

Prepare the bearing frame (228) as follows (see the illustration):

a) Install the oil-fill plug (113A).

b) Install the oil-drain plug (408A).

c)

Install the sight glass (319).

d) Install the sight oiler plug (408J).

e) Install the plug for the oil-cooler inlet (408L).

f)

Install the plug for the oil-cooler outlet (408M).

g) Install four oil-mist connection plugs (408H).

Or: Install two grease fittings (193) and two grease-relief plugs (113).

h) Attach the bearing-frame foot (241) and fasten the bolts (370F) by hand.

6.6 Reassembly

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

109

«
...
109
110
111
112
113
...
»

Summary of Contents for Goulds Pumps CV 3196 i-FRAME



















































































































































































Reviews:

No comments

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brand: Gardena Pages: 13

Brand: WarmFlow Pages: 89

Brand: EasyPro Pages: 8

Brand: Wayne Pages: 8

Brand: Balcrank Pages: 18

45 E Frame Series

Brand: Danfoss Pages: 44

ElectriFLEX LD LE Series

Brand: Bradford White Pages: 40

Brand: Barnstead|Thermolyne Pages: 56

Shurflo 8000 Series

Brand: Lilie Pages: 6

CLIMAGUARD TX23

Brand: McLean Pages: 20

Brand: Mixtron Pages: 44

Brand: KISANKRAFT Pages: 44

Brand: T.I.P. Pages: 104

Brand: Bard Pages: 42

Brand: Zodiac Pages: 16

Brand: Kawamoto Pump Pages: 28

Brand: Oase Pages: 76

WS G140DC6 Series

Brand: Waterstage Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands