ITT Goulds Pumps CV 3196 i-FRAME Installation, Operation And Maintenance Manual Download Page 125 | Manualshive

Page: 125 / 178

background image

NOTICE:

Ensure that the pipe threads are clean. Apply thread sealant to the plugs and fittings. Failure to
do so may result in oil leaks and equipment damage.

NOTICE:

There are several methods used to install bearings. The recommended method is to use an
induction heater that heats as well as demagnetizes the bearings. Failure to use this method
may result in equipment damage.

1.

Prepare the bearing frame (228) as follows (see the illustration):

a) Install the oil-fill plug (113A).

b) Install the oil-drain plug (408A).

c)

Install the sight glass (319).

d) Install the sight oiler plug (408J).

e) Install the plug for the oil-cooler inlet (408L).

f)

Install the plug for the oil-cooler outlet (408M).

g) Install four oil-mist connection plugs (408H).

Or: Install two grease fittings (193) and two grease-relief plugs (113).

370F

241

408A

408L

319

228A

113A

408N

408M

2.

Install the outboard bearings (112A) on the shaft (122).

The regreasable bearing has a single shield. Make sure that the bearing is installed with the shield
away from the impeller.

The duplex bearings are mounted back-to-back. Make sure that the orientation of the bearings are
correct.

a) Inspect the shaft (122) to ensure that it is clean, dimensionally correct, and is free of nicks and

burrs.

6.6 Reassembly

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

123

«
...
123
124
125
126
127
...
»

Summary of Contents for Goulds Pumps CV 3196 i-FRAME



















































































































































































Reviews:

No comments

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brand: A.O. Smith Pages: 20

Brand: A.O. Smith Pages: 4

Brand: A.O. Smith Pages: 24

Brand: A.O. Smith Pages: 6

Brand: A.O. Smith Pages: 2

Brand: A.O. Smith Pages: 2

Brand: xFyre Pages: 60

Brand: A.O. Smith Pages: 8

Brand: A.O. Smith Pages: 4

Brand: A.O. Smith Pages: 6

Brand: A.O. Smith Pages: 40

Brand: Calpeda Pages: 44

Brand: Calpeda Pages: 64

Brand: Calpeda Pages: 32

Brand: Zoeller Pages: 12

Taro HCS SJ Series

Brand: Texmo Industries Pages: 41

Brand: Takagi Pages: 64

Brand: A.O. Smith Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands