ITT Goulds Pumps CV 3196 i-FRAME Installation, Operation And Maintenance Manual Download Page 130 | Manualshive

Page: 130 / 178

background image

SCALE

0.150

Figure 114: Remove impeller and shaft sleeve

4.

Check the frame-face run-out by rotating the shaft so that the indicator measures the fit for 360º.
If the total indicator reading is greater than 0.025 mm | 0.001 in., then disassemble and determine
the cause.

Figure 115: Check frame-face run-out

5.

Place the manila gasket (360D) on the frame (228), and hold the gasket in place by inserting the
dowel pins (469B) in their holes.
The gasket is designed to fit only one way.

6.

Install the frame adapter.

a) Place the frame adapter (108) onto the frame assembly.

b) Align the bolt holes and dowel locations on the frame adapter with the bolt holes and dowel lo-

cations on the frame.

6.6 Reassembly

128

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

«
...
128
129
130
131
132
...
»

Summary of Contents for Goulds Pumps CV 3196 i-FRAME



















































































































































































Reviews:

No comments

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brand: Gardena Pages: 17

Little Sea-ox FCD-30

Brand: Haier Pages: 23

Brand: Palm Pages: 20

Brand: Bard Pages: 50

Clima Canal JDPC.002

Brand: Jaga Pages: 8

Brand: Wacker Neuson Pages: 44

Water Solutions 3098 Series

Brand: Zoeller Pages: 4

Aquanot Spin 508

Brand: Zoeller Pages: 2

Brand: Zoeller Pages: 11

Brand: Zip Pages: 18

Brand: T.I.P. Pages: 104

Brand: Daikin Pages: 316

Brand: Magic-Pak Pages: 18

Brand: Wanner Engineering Pages: 24

3D TRASAR Series

Brand: Nalco Pages: 243

AlwaysFresh HFC-1000

Brand: Waterline Technology Pages: 6

Brand: Oase Pages: 31

Brand: Oasis Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands