ITT Goulds Pumps CV 3196 i-FRAME Installation, Operation And Maintenance Manual Download Page 33

Page: 33 / 178

The correct height depends on the required distance between the foundation/floor and the base-
plate.

Put a washer onto the lower adjusting- nut.

Install the stilt assembly on the baseplate:

a) Insert the stilt assembly into the baseplate's anchorage hole from below.

b) Put a washer onto the stilt.

Fasten the stilt assembly with the upper adjusting nut by hand.

Screw the upper jam nut onto the stilt by hand.

Repeat steps 2 through 4 for all the stilt assemblies.

Lower the baseplate so that the stilts fit into the foundation cups.

Level the baseplate and make the final height adjustments:

a) Loosen the upper jam nuts and adjusting nuts.

b) Adjust the height and level the baseplate by moving the lower adjusting nuts.

When the baseplate is level, tighten the top adjusting nuts.

Fasten the lower and upper jam nuts on each stilt.

Mounting plate

Mounting nut

Stilt bolt

Foundation cups

Washer

Upper adjustment nut

Mounting washer

Mounting bolt

Figure 22: Example of an installed stilt assembly

4.2 Baseplate-mounting procedures

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

Summary of Contents for Goulds Pumps CV 3196 i-FRAME



















































































































































































Search results

Summary of Contents for Goulds Pumps CV 3196 i-FRAME

Reviews:

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brands by name

Popular brands

ITT Goulds Pumps CV 3196 i-FRAME, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Goulds Pumps CV 3196 i-FRAME

Reviews:

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brands by name

Popular brands