ITT Goulds Pumps CV 3196 i-FRAME Installation, Operation And Maintenance Manual Download Page 127

Page: 127 / 178

See the specified torque values.

Make sure that the shaft rotates freely.

109A

371C

360C

134

Install the inboard bearing as follows (see the illustration):

a) Coat the inner surfaces of the bearings with lubricant.

b) Put the inboard bearing (168) onto the shaft (122).

The regreasable bearing has a single shield. Make sure that the bearing is installed with the shield
away from the impeller.

122

168A

Install the remaining parts onto the bearing shaft as follows (see the illustration):

a) Install a new O-ring (496).

b) Install the outboard labyrinth oil-seal (332A) into the end cover (109A).

Place the drain slots of the oil seal at the bottom position (6 o’clock).

Make sure that the edges of the keyway are free from burrs. To protect the O-ring, cover the keyway
lengthwise with a piece of electrical tape before you install the oil seal.

332A

109A

496

10. Install the shaft assembly into the bearing frame as follows (see the illustration):

a) Coat the outside of the bearing housing (134) with oil.

6.6 Reassembly

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

125

Summary of Contents for Goulds Pumps CV 3196 i-FRAME



















































































































































































Search results

Summary of Contents for Goulds Pumps CV 3196 i-FRAME

Reviews:

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brands by name

Popular brands

ITT Goulds Pumps CV 3196 i-FRAME, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Goulds Pumps CV 3196 i-FRAME

Reviews:

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brands by name

Popular brands