ITT Goulds Pumps CV 3196 i-FRAME Installation, Operation And Maintenance Manual Download Page 44

Page: 44 / 178

Example: Installation for expansion

Correct

Incorrect

This illustration shows a correct installation for expan-
sion:

Expansion loop/joint

This illustration shows an incorrect installation for expan-
sion:

4.6.1.1 Fastening

WARNING:

Risk of serious personal injury or property damage. Fasteners such as bolts and nuts are criti-
cal to the safe and reliable operation of the product. Ensure appropriate use of fasteners during
installation or reassembly of the unit.

•

Use fasteners of the proper size and material only.

•

Replace all corroded fasteners.

•

Ensure that all fasteners are properly tightened and that there are no missing fasteners.

4.6.2 Suction-piping checklist

Performance curve reference

Net positive suction head available (NPSH

) must always exceed NPSH required (NPSH

) as shown on

the published performance curve of the pump.

Suction-piping checks

Check

Explanation/comment

Checked

Check that the distance between the inlet
flange of the pump and the closest elbow
is at least five pipe diameters.

This minimizes the risk of cavitation in the suction in-
let of the pump due to turbulence.

See the Example sections for illustrations.

Check that elbows in general do not have
sharp bends.

See the Example sections for illustrations.

—

4.6 Piping checklists

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

Summary of Contents for Goulds Pumps CV 3196 i-FRAME



















































































































































































Search results

Summary of Contents for Goulds Pumps CV 3196 i-FRAME

Reviews:

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brands by name

Popular brands

ITT Goulds Pumps CV 3196 i-FRAME, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Goulds Pumps CV 3196 i-FRAME

Reviews:

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brands by name

Popular brands