ITT Goulds Pumps CV 3196 i-FRAME Installation, Operation And Maintenance Manual Download Page 75 | Manualshive

Page: 75 / 178

background image

6.2.1.2 Acceptable oil for lubricating bearings

Acceptable lubricants

Table 13: Acceptable lubricants

Brand

Lubricant type

Chevron

GST Oil 68

Exxon

Teresstic EP 68

Mobil

DTE Heavy Medium

Phillips 66

Turbine Oil VG68

Shell

Turbo T 68

Sunoco

Sunvis 968

Royal Purple SYNFILM ISO VG 68 Synthetic Oil

6.2.2 Regrease the grease-lubricated bearings

NOTICE:

Risk of equipment damage. Ensure that the grease container, the greasing device, and the fit-
tings are clean. Failure to do so can result in impurities entering the bearing housing while re-
greasing the bearings.

193

113

Figure 48: Bearing lubrication

1.

Wipe dirt from the grease fittings.

2.

Remove the two grease-relief plugs from the bottom of the frame.

3.

Fill both of the grease cavities through the fittings with a recommended grease until the fresh
grease comes out of the relief holes.

4.

Make sure that the frame seals are seated in the bearing housing.
If they are not, press them in place with the drains located at the bottom.

5.

Reinstall the grease-relief plugs.

6.

Wipe off any excess grease.

7.

Recheck the alignment.

The bearing temperature usually rises after you regrease due to an excess supply of grease. Tempera-
tures return to normal in about two to four operating hours as the pump runs and purges the excess
grease from the bearings.

6.2 Bearing maintenance

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

73

«
...
73
74
75
76
77
...
»

Summary of Contents for Goulds Pumps CV 3196 i-FRAME



















































































































































































Reviews:

No comments

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brand: Barnes Pages: 12

Brand: Zip Pages: 12

Brand: Oasis Pages: 44

PacificHydrostar 2" Gasoline Powered Clear Water...

Brand: Pacific hydrostar Pages: 24

Brand: Cordivari Pages: 44

Brand: Tiger Pages: 36

Brand: A.O. Smith Pages: 48

Brand: Campbell Pages: 2

Brand: Daikin Pages: 44

Brand: Edwards Pages: 60

Brand: La Buvette Pages: 44

150L SunStream Indirect

Brand: SUNSCAN Pages: 24

FIGHTER 2010 Series

Brand: Nibe Pages: 36

Brand: Bard Pages: 41

Brand: Uni-max Pages: 6

EASY CLEAR EQ-12-TH

Brand: Bunn Pages: 2

Brand: F.B. SUBMERSIBLE MOTORS Pages: 48

Brand: hajdu Pages: 65

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands