ITT Goulds Pumps CV 3196 i-FRAME Installation, Operation And Maintenance Manual Download Page 103

Page: 103 / 178

Dynamic-seal repeller replacement

This table shows the criteria for replacing dynamic-seal repeller parts for the 3196, CV 3196, and LF 3196
pump models.

Dynamic seal part

When to replace

Dynamic-seal repeller vane The grooves are deeper than 1.6 mm | 1/16 in. or are worn evenly more than 0.8 mm |

1/32 in..

Sleeve surface

The surface has grooves, pitting, or other damage.

Labyrinth seal replacement

Replace the labyrinth-seal O-ring if it has cuts and cracks.

Gaskets, O-rings, and seats replacement

WARNING:

Risk of death or serious injury. Leaking fluid can cause fire and/or burns. Replace all gaskets
and O-rings at each overhaul or disassembly.

•

Replace all gaskets and O-rings at each overhaul and disassembly.

•

Inspect the seats. They must be smooth and free of physical defects.

•

In order to repair worn seats, skin cut them in a lathe while you maintain dimensional relationships
with other surfaces.

•

Replace parts if the seats are defective.

Fasteners

WARNING:

Risk of serious personal injury or property damage. Fasteners such as bolts and nuts are criti-
cal to the safe and reliable operation of the product. Ensure appropriate use of fasteners during
installation or reassembly of the unit.

•

Use fasteners of the proper size and material only.

•

Replace all corroded fasteners.

•

Ensure that all fasteners are properly tightened and that there are no missing fasteners.

6.5.1.1 Fastening

WARNING:

•

Use fasteners of the proper size and material only.

•

Replace all corroded fasteners.

•

Ensure that all fasteners are properly tightened and that there are no missing fasteners.

6.5 Pre-assembly inspections

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

101

Summary of Contents for Goulds Pumps CV 3196 i-FRAME



















































































































































































Search results

Summary of Contents for Goulds Pumps CV 3196 i-FRAME

Reviews:

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brands by name

Popular brands

ITT Goulds Pumps CV 3196 i-FRAME, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Goulds Pumps CV 3196 i-FRAME

Reviews:

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brands by name

Popular brands