ITT Goulds Pumps CV 3196 i-FRAME Installation, Operation And Maintenance Manual Download Page 94

Page: 94 / 178

NOTICE:

Use force only on the inner race when pressing bearings from the shaft. Failure to do so may
result in equipment damage.

NOTICE:

Do not reuse bearings if removed from shaft. Doing so may result in equipment damage. Re-
place the bearings before reassembly.

11. Remove the outboard labyrinth oil seal (332A) from the bearing housing (134).

Remove the O-rings (497F and 497G) if it is necessary. Labyrinth oil seal O-rings are part of the
3196 maintenance kits and they are sold separately.

497G

332A

497F

Figure 76: Outboard labyrinth oil seal removal

6.4.15.3 Disassemble the power end (LTi)

Remove the clamp screws (370C) and back off the jam nuts (423).

Evenly tighten the jack screws (370D) to move the bearing housing (134) out of the bearing frame
(228A).

Remove the shaft assembly from the bearing frame (228A).

228A

134

370D

423

370C

Figure 77: Shaft assembly removal

Remove the jack screws (370D) with the nuts (423).

Remove the clamp-ring screws (236A) and separate the clamp ring (253B) from the bearing hous-
ing (134).

You must remove the bearings before you can remove the clamp ring from the shaft.

6.4 Disassembly

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

Summary of Contents for Goulds Pumps CV 3196 i-FRAME



















































































































































































Search results

Summary of Contents for Goulds Pumps CV 3196 i-FRAME

Reviews:

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brands by name

Popular brands

ITT Goulds Pumps CV 3196 i-FRAME, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Goulds Pumps CV 3196 i-FRAME

Reviews:

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brands by name

Popular brands