ITT Goulds Pumps CV 3196 i-FRAME Installation, Operation And Maintenance Manual Download Page 124 | Manualshive

Page: 124 / 178

background image

332A

109A

496

10. Install the shaft assembly into the bearing frame as follows (see the illustration):

a) Coat the outside of the bearing housing (134) with oil.

b) Coat all the internal surfaces of the bearing frame (228) with oil.

c)

Install the shaft assembly into the bearing frame (228).

Make sure that the shaft rotates freely.

d) Install the clamp bolts (370C) in the bearing housing (134) and tighten by hand.

e) Install the jack bolts (370D) with the locknuts (423) in the bearing housing (134) and tighten by

hand.

f)

Attach the bearing-frame foot (241) and fasten the bolts (370F) by hand.

228A

134

370D

423

370C

6.6.5 Assemble the rotating element and the bearing frame (XLT-i and i17
with duplex bearings)

WARNING:

Lifting and handling heavy equipment or components poses a crush hazard. Use caution dur-
ing lifting and handling and wear appropriate Personal Protective Equipment (PPE, such as
steel-toed shoes, gloves, etc.) at all times. Seek assistance if necessary.

CAUTION:

Risk of physical injury from hot bearings. Wear insulated gloves when using a bearing heater.

6.6 Reassembly

122

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

«
...
122
123
124
125
126
...
»

Summary of Contents for Goulds Pumps CV 3196 i-FRAME



















































































































































































Reviews:

No comments

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brand: PAPILLON Pages: 22

Brand: Waterous Pages: 10

VRV EMERION RXYQ-AATJA

Brand: Daikin Pages: 429

Brand: A.O. Smith Pages: 4

Brand: York Pages: 204

Brand: GEA Pages: 337

BTR(C)120 THRU 500A

Brand: A.O. Smith Pages: 36

Brand: Econo Pages: 27

Brand: deconta Pages: 12

Brand: Wacker Neuson Pages: 60

H Design Series

Brand: Continental Hydraulics Pages: 8

Brand: DAXOM Pages: 20

Brand: Silverline Pages: 2

Brand: Warren rupp Pages: 16

FLOW-PRO 350MOP

Brand: EUROM Pages: 32

Brand: Buck Pages: 2

Brand: Wilo Pages: 20

Brand: Sunsystem Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands