ITT Goulds Pumps CV 3196 i-FRAME Installation, Operation And Maintenance Manual Download Page 115

Page: 115 / 178

Install the sight glass (319).

d) Install the sight oiler plug (408J).

e) Install the plug for the oil-cooler inlet (408L).

Install the plug for the oil-cooler outlet (408M).

g) Install four oil-mist connection plugs (408H).

Or: Install two grease fittings (193) and two grease-relief plugs (113).

h) Attach the bearing-frame foot (241) and fasten the bolts (370F) by hand.

319

408N

408A

241

370F

408N

408W

372T

113A

408W

408M

761B

Figure 101: Bearing frame foot reassembly

Install the outboard bearings (112A) on the shaft (122).

The regreasable bearing has a single shield. Make sure that the bearing is installed with the shield
away from the impeller.

The duplex bearings are mounted back-to-back. Make sure that the orientation of the bearings are
correct.

a) Inspect the shaft (122) to ensure that it is clean, dimensionally correct, and is free of nicks and

burrs.

122

112

136

Figure 102: Shaft inspection

b) Lightly coat the bearing seating with a thin film of oil.

Remove the bearings (112) from their packaging.

d) Wipe the preservative from the bearing (112) bore and outer diameter.

6.6 Reassembly

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

113

Summary of Contents for Goulds Pumps CV 3196 i-FRAME



















































































































































































Search results

Summary of Contents for Goulds Pumps CV 3196 i-FRAME

Reviews:

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brands by name

Popular brands

ITT Goulds Pumps CV 3196 i-FRAME, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Goulds Pumps CV 3196 i-FRAME

Reviews:

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brands by name

Popular brands