ITT Goulds Pumps CV 3196 i-FRAME Installation, Operation And Maintenance Manual Download Page 114 | Manualshive

Page: 114 / 178

background image

Make sure that the shaft rotates freely.

d) Install the clamp bolts (370C) in the bearing housing (134) and tighten by hand.

e) Install the jack bolts (370D) with the locknuts (423) in the bearing housing (134) and tighten by

hand.

134

370D

423

228A

370C

Figure 100: Jack bolt and locknut reassembly

6.6.2 Assemble the rotating element and the bearing frame (STi and MTi
with duplex bearings)

WARNING:

Lifting and handling heavy equipment or components poses a crush hazard. Use caution dur-
ing lifting and handling and wear appropriate Personal Protective Equipment (PPE, such as
steel-toed shoes, gloves, etc.) at all times. Seek assistance if necessary.

CAUTION:

Risk of physical injury from hot bearings. Wear insulated gloves when using a bearing heater.

NOTICE:

Ensure that the pipe threads are clean. Apply thread sealant to the plugs and fittings. Failure to
do so may result in oil leaks and equipment damage.

NOTICE:

There are several methods used to install bearings. The recommended method is to use an
induction heater that heats as well as demagnetizes the bearings. Failure to use this method
may result in equipment damage.

1.

Prepare the bearing frame (228) as follows (see the illustration):

a) Install the oil-fill plug (113A).

b) Install the oil-drain plug (408A).

6.6 Reassembly

112

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

«
...
112
113
114
115
116
...
»

Summary of Contents for Goulds Pumps CV 3196 i-FRAME



















































































































































































Reviews:

No comments

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brand: salmson Pages: 49

Brand: York Pages: 4

Nessie Plug&Spray NPS 1CS

Brand: Danfoss Pages: 12

Brand: Reefe Pages: 12

Brand: Davey Pages: 20

Brand: Rinnai Pages: 18

Brand: Rinnai Pages: 67

Brand: Wilo Pages: 76

Brand: salmson Pages: 16

Brand: Fairland Pioneer Pages: 36

Brand: SAER Elettropompe Pages: 44

Brand: Kärcher Pages: 50

Brand: Oase Pages: 42

Brand: GORMAN-RUPP PUMPS Pages: 25

Brand: Intex Pages: 5

Brand: GDH Pages: 24

Brand: Samoa Pages: 82

HOTSPRING HSTK5

Brand: ZANSKAR Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands