ITT Goulds Pumps CV 3196 i-FRAME Installation, Operation And Maintenance Manual Download Page 30 | Manualshive

Page: 30 / 178

background image

NOTICE:

Remove all dirt from the mounting pads in order to ensure that the correct leveling is achieved.
Failure to do so can result in equipment damage or decreased performance.

a) Put one machinist's level lengthwise on one of the two pads.

b) Put the other machinist's level across the ends of the two pads.

c)

Level the pads by adjusting the four jackscrews in the corners.

Make sure that the machinist's level readings are as close to zero as possible, both lengthwise and
across.

Use the baseplate-leveling worksheet when you take the readings.

1

2

3

4

5

6

Item Description

1.

Machinist's levels

2.

Driver's mounting pads

3.

Foundation bolts

4.

Jackscrews

5.

Grout hole

6.

Pump's mounting pads

Figure 19: Level driver mounting pads

4.

Turn the center jackscrews down so that they rest on their plates on the foundation surface.

5.

Level the pump mounting pads:

NOTICE:

Remove all dirt from the mounting pads in order to ensure that the correct leveling is achieved.
Failure to do so can result in equipment damage or decreased performance.

a) Put one machinist's level lengthwise on one of the two pads.

b) Put the other level across the center of the two pads.

c)

Level the pads by adjusting the four jackscrews in the corners.

Make sure that the machinist's level readings are as close to zero as possible, both lengthwise and
across.

4.2 Baseplate-mounting procedures

28

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

«
...
28
29
30
31
32
...
»

Summary of Contents for Goulds Pumps CV 3196 i-FRAME



















































































































































































Reviews:

No comments

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brand: Waterous Pages: 13

Brand: Waterous Pages: 57

Brand: ubbink Pages: 29

Brand: YANGTECH Pages: 23

Brand: Osram Pages: 8

Brand: OLIJU Pages: 28

LEH150-E Series

Brand: Liberty Pumps Pages: 83

Brand: Nibe Pages: 44

Brand: Wilo Pages: 80

Brand: Reefe Pages: 12

Brand: Davey Pages: 20

Brand: Rinnai Pages: 2

Brand: York Pages: 24

Brand: Warren rupp Pages: 22

Brand: Mannesmann Pages: 3

TURBO-FLUX modular

Brand: Cattani Pages: 61

Brand: RainScapes Pages: 2

Brand: Redring Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands