ITT Goulds Pumps CV 3196 i-FRAME Installation, Operation And Maintenance Manual Download Page 87

Page: 87 / 178

184

355

250

370H

Figure 59: Seal chamber cover removal

Remove the shaft sleeve (126) if it is used.
The mechanical seal is attached to the sleeve.

NOTICE:

Be careful with the mechanical seal. Carbon or ceramic components are brittle and easily bro-
ken.

Remove the rotary portion of the seal from the sleeve by loosening the setscrews and sliding it off
the sleeve.
Refer to the mechanical-seal instructions for more information.

Remove the gland (250), the stationary portion of the seal, and the O-ring (360Q).

126

383

360Q

383

250

Figure 60: Gland removal

6.4.11 Remove the stuffing-box cover (3196, CV 3196, HT 3196, LF 3196,
3796)

Remove the gland nuts (355) and the gland (107).

Remove the stuffing-box-cover nuts (370H).

Remove the stuffing-box cover (184).

6.4 Disassembly

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

Summary of Contents for Goulds Pumps CV 3196 i-FRAME



















































































































































































Search results

Summary of Contents for Goulds Pumps CV 3196 i-FRAME

Reviews:

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brands by name

Popular brands

ITT Goulds Pumps CV 3196 i-FRAME, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Goulds Pumps CV 3196 i-FRAME

Reviews:

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brands by name

Popular brands