ITT Goulds Pumps CV 3196 i-FRAME Installation, Operation And Maintenance Manual Download Page 121 | Manualshive

Page: 121 / 178

background image

228A

134

370D

423

370C

Figure 111: Jack bolt and locknut installation

6.6.4 Assemble the rotating element and the bearing frame (XLT-i and i17)

WARNING:

Lifting and handling heavy equipment or components poses a crush hazard. Use caution dur-
ing lifting and handling and wear appropriate Personal Protective Equipment (PPE, such as
steel-toed shoes, gloves, etc.) at all times. Seek assistance if necessary.

CAUTION:

Risk of physical injury from hot bearings. Wear insulated gloves when using a bearing heater.

NOTICE:

Ensure that the pipe threads are clean. Apply thread sealant to the plugs and fittings. Failure to
do so may result in oil leaks and equipment damage.

NOTICE:

There are several methods used to install bearings. The recommended method is to use an
induction heater that heats as well as demagnetizes the bearings. Failure to use this method
may result in equipment damage.

1.

Prepare the bearing frame (228) as follows (see the illustration):

a) Install the oil-fill plug (113A).

b) Install the oil-drain plug (408A).

c)

Install the sight glass (319).

d) Install the sight oiler plug (408J).

e) Install the plug for the oil-cooler inlet (408L).

f)

Install the plug for the oil-cooler outlet (408M).

g) Install four oil-mist connection plugs (408H).

Or: Install two grease fittings (193) and two grease-relief plugs (113).

6.6 Reassembly

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

119

«
...
119
120
121
122
123
...
»

Summary of Contents for Goulds Pumps CV 3196 i-FRAME



















































































































































































Reviews:

No comments

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brand: Bacharach Pages: 12

Nano-Flow 2,600

Brand: Cobalt Digital Inc Pages: 2

Brand: Endress Pages: 17

AQUAPRO AP1000FP

Brand: Aquatec Pages: 2

Brand: EBARA Pages: 28

RoadLazer Husky 515

Brand: Graco Pages: 2

Delta Plus UE 35A-XX PWM Series

Brand: WITA Pages: 36

SCM 4 PLUS 115/92

Brand: Flotec Pages: 22

Brand: GPI Pages: 26

FlowMaster 85850

Brand: Lincoln Pages: 25

Brand: Penguin Pages: 10

Brand: Davey Pages: 20

Brand: DAYLIFF Pages: 12

Econoboil 301642

Brand: Zenith Pages: 12

Brand: JABSCO Pages: 4

Sandpiper S20 Metallic

Brand: Warren rupp Pages: 24

smart clima 12170027

Brand: Tecnosystemi Pages: 8

Brand: Carrier Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands