ITT Goulds Pumps CV 3196 i-FRAME Installation, Operation And Maintenance Manual Download Page 32 | Manualshive

Page: 32 / 178

background image

4.

Thread the upper jam nut onto the spring stud by hand.

5.

Repeat steps 2 through 4 for all the spring assemblies.

6.

Lower the baseplate so that the spring assemblies fit into the foundation pads.

7.

Level the baseplate and make the final height adjustments:

a) Loosen the upper jam nuts and adjusting nuts.

b) Adjust the height and level the baseplate by moving the lower adjusting nuts.

c)

When the baseplate is level, tighten the top adjusting nuts so that the top springs are not loose
in their followers.

8.

Fasten the lower and upper jam nuts on each spring assembly.

1

2

3

4

5

6

7

1.

Upper jam nut

2.

Follower

3.

Washer

4.

Foundation pads

5.

Spring

6.

Upper adjusting nut

7.

Spring stud

Figure 21: Example of an installed spring assembly

4.2.5 Install the baseplate using stilt mounting

NOTICE:

The stilt-mounted baseplate is not designed to support static piping loads. Ensure that the suc-
tion and discharge piping are supported individually. Failure to do so may result in equipment
damage.

1.

Put the baseplate on a support above the foundation/floor.
Make sure that there is enough space between the baseplate and the foundation/floor to install the
stilts.

2.

Install the lower part of the stilt assembly:

a) Screw the lower jam nut and adjusting nut onto the stilt.

b) Set the lower adjusting nut to the correct height.

4.2 Baseplate-mounting procedures

30

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

«
...
30
31
32
33
34
...
»

Summary of Contents for Goulds Pumps CV 3196 i-FRAME



















































































































































































Reviews:

No comments

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brand: YAMADA Pages: 18

Goulds Marlow Series

Brand: Xylem Pages: 8

Brand: Xylem Pages: 12

Brand: QEP Pages: 2

Brand: Kärcher Pages: 16

Brand: ICON Pages: 16

Brand: Atlas Copco Pages: 137

Brand: A.O. Smith Pages: 119

Brand: Kessel Pages: 24

Brand: Barracuda PUMPS Pages: 4

Brand: York Pages: 24

Brand: Xylem Pages: 44

Brand: GE Pages: 28

Brand: Navien Pages: 131

Brand: Annovi Reverberi Pages: 4

DSE-5 THRU DSE-120

Brand: A.O. Smith Pages: 24

Brand: clage Pages: 148

Brand: Unitary products group Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands