ITT Goulds Pumps CV 3196 i-FRAME Installation, Operation And Maintenance Manual Download Page 60 | Manualshive

Page: 60 / 178

background image

Slide to fit

Driver

Figure 41: Slide driver-half of coupling guard towards motor

10. Use a nut, a bolt, and two washers to secure the coupling guard halves together.

11. Tighten all nuts on the guard assembly.

5.6.2 Bearing lubrication

WARNING:

Risk of explosive hazard and premature failure from sparks and heat generation. Ensure

bearings are properly lubricated prior to startup.

NOTICE:

Grease can settle in equipment left idle leaving bearings improperly lubricated. Check the
greasing on a pump that has been out of service for a long period of time and re-grease if nec-
essary.

Pumps are shipped without oil. You must lubricate oil-lubricated bearings at the job site.

Grease-lubricated bearings are lubricated at the factory.

The bearing manufacturer fills greased-for-life bearings with grease and seals them at the factory. You do
not need to lubricate or seal these bearings.

5.6.2.1 Oil volumes

Oil volume requirements

This table shows the required amount of oil for oil-lubricated bearings.

Frame

ml

Qts.

Oz.

STi

400

0.5

16

MTi

1400

1.5

47

LTi

1400

1.5

48

XLT-i and i17

3000

3

96

5.6 Couple the pump and driver

58

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

«
...
58
59
60
61
62
...
»

Summary of Contents for Goulds Pumps CV 3196 i-FRAME



















































































































































































Reviews:

No comments

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brand: Maag Pages: 16

Brand: A.O. Smith Pages: 40

Brand: TapFlo Pages: 35

Brand: Waters Pages: 111

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 2

Brand: Danfoss Pages: 38

Infinite Energy2 IW1000

Brand: RBI Pages: 156

Brand: ESBE Pages: 28

Brand: Danfoss Pages: 12

Brand: EINHELL Pages: 44

Brand: Speck Pages: 24

Brand: T.I.P. Pages: 136

PROTÉGÉ RPAGP

Brand: Raypak Pages: 3

Brand: Gianneschi Pages: 28

Brand: Cosmo Pages: 48

Brand: Wacker Neuson Pages: 60

CLI U12 SD0F1110 NG B/U

Brand: Velux Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands