ITT Goulds Pumps CV 3196 i-FRAME Installation, Operation And Maintenance Manual Download Page 108

Page: 108 / 178

6.5.6 Bearings inspection

Condition of bearings

Do not reuse bearings. The condition of the bearings provides useful information on operating conditions
in the bearing frame.

Checklist

Perform these checks when you inspect the bearings:

•

Inspect the bearings for contamination and damage.

•

Note any lubricant condition and residue.

•

Inspect the ball bearings to see if they are loose, rough, or noisy when you rotate them.

•

Investigate any bearing damage to determine the cause. If the cause is not normal wear, correct
the issue before you return the pump to service.

6.5.7 Bearing-housing inspection

Checklist

•

Inspect the bearing-housing (134) bore according to the bearing fits and tolerances table.

•

Replace the bearing housing if the dimensions exceed acceptable values. Reference: see Bearings
fits and tolerances.

•

Visually inspect the bearing housing for cracks and pits.

Checklist for specific models

This table shows bearing-housing checks that are required for specific models of pump.

Frame

Bearing-housing check

STi and MTi Ensure that the snap-ring groove is not cracked.
LTi

Clear all grooves and holes.

XLT-i

Clean the gasket surface.

Inspection locations

The following images point to the areas to inspect on the bearing housing.

6.5 Pre-assembly inspections

106

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

Summary of Contents for Goulds Pumps CV 3196 i-FRAME



















































































































































































Search results

Summary of Contents for Goulds Pumps CV 3196 i-FRAME

Reviews:

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brands by name

Popular brands

ITT Goulds Pumps CV 3196 i-FRAME, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Goulds Pumps CV 3196 i-FRAME

Reviews:

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brands by name

Popular brands