ITT Goulds Pumps CV 3196 i-FRAME Installation, Operation And Maintenance Manual Download Page 100 | Manualshive

Page: 100 / 178

background image

•

oil-cooler inlet and outlet plugs (408L and 408M) or oil cooler

2.

For the MTi and LTi models, remove the bearing frame foot-to-frame bolts (370F) and the frame foot
(241).

319

408N

408A

241

370F

408N

408W

372T

113A

408W

408M

761B

Figure 82: Plug removal

6.4.17 Guidelines for i-ALERT

®

2 Equipment Health Monitor disposal

Precautions

WARNING:

•

Explosive hazard and risk of personal injury. Heating to high temperatures could cause
combustion of the condition monitor. Never heat the condition monitor to temperatures in
excess of 149°C | 300°F or dispose of in a fire.

Guidelines

The battery contained in the condition monitor does not contain enough lithium to qualify as reactive haz-
ardous waste. Use these guidelines when disposing of the condition monitor.

•

The condition monitor is safe for disposal in the normal municipal waste stream.

•

Adhere to local laws when you dispose of the condition monitor.

6.4.18 Disassemble the C-face adapter

WARNING:

Risk of personal injury and equipment damage from dropping or tipping motor. The motor must
be properly supported with a clean, uncorroded eye bolt or a strap under both ends.

1.

Loosen the motor-mounting bolts and remove the motor.

6.4 Disassembly

98

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

«
...
98
99
100
101
102
...
»

Summary of Contents for Goulds Pumps CV 3196 i-FRAME



















































































































































































Reviews:

No comments

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brand: 4rain Pages: 44

Brand: Navien Pages: 48

Brand: Navien Pages: 2

Brand: Calpeda Pages: 32

Brand: RainSoft Pages: 16

Brand: GE Pages: 1

Brand: Powerhorse Pages: 48

Altherma 3 M Series

Brand: Daikin Pages: 24

T4BD-018K Series

Brand: Nordyne Pages: 4

Wilden A2550V Series

Brand: PSG Pages: 16

Brand: DAB Pages: 72

Brand: AQUASYSTEM Pages: 12

Serve Better CP-RP

Brand: Server Pages: 8

Brand: RBI Pages: 44

Brand: Bard Pages: 38

Brand: A.O. Smith Pages: 6

Brand: Pro-Craft Pages: 24

ProSeries Chem-Feed CFPS-1

Brand: Blue-White industries Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands