ITT Goulds Pumps CV 3196 i-FRAME Installation, Operation And Maintenance Manual Download Page 151

Page: 151 / 178

6.6.16.3 Bearing types

Table 25: Bearing types

Frame

Inboard bearing

Outboard bearing

Double row

Duplex

STi

6207

3306

7306

MTi

6309

3309

7309

LTi

6311

Not applicable

7310

XLT-i, i17

6313

3313

7313

6.6.17 Spare parts

Always state the serial number and indicate the part name and item number from the relevant sectional
drawing when you order spare parts. It is imperative for service reliability to have a sufficient stock of
readily available spare parts.

•

Impeller (101)

•

Shaft (122A)

•

Shaft sleeve (126)

•

Outboard bearing (112A)

•

Inboard bearing (168A)

•

Casing gasket (351)

•

Frame-to-adapter gasket (360D)

•

Bearing-housing retaining ring (361A)

•

Bearing lockwasher (382)

•

Bearing locknut (136)

•

Impeller O-ring (412A)

•

Bearing-housing O-ring (496)

•

Outboard labyrinth-seal rotary O-ring (497F)

•

Outboard labyrinth-seal stationary O-ring (497G)

•

Inboard labyrinth-seal rotary O-ring (497H)

•

Inboard labyrinth-seal stationary O-ring (497J)

•

Lantern ring half (105) (packed stuffing box)

•

Stuffing box packing (106) (packed stuffing box)

•

Packing gland (107) (packed stuffing box)

•

Impeller gasket (428D) (XLT-i and i17 only)

6.7 Interchangeability drawings

6.7.1 CV 3196 interchangeability

Table 26: CV 3196 interchangeability drawing

Description

Shaft and Bearing

Frame Assembly

Adapter Seal Chamber Impeller

Casing

Size

Model CV 3196
STi 1–3/8 in.
Shaft Dia. Max
BHP-40 HP

2x2-8

6.7 Interchangeability drawings

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

149

Summary of Contents for Goulds Pumps CV 3196 i-FRAME



















































































































































































Search results

Summary of Contents for Goulds Pumps CV 3196 i-FRAME

Reviews:

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brands by name

Popular brands

ITT Goulds Pumps CV 3196 i-FRAME, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Goulds Pumps CV 3196 i-FRAME

Reviews:

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brands by name

Popular brands