ITT Goulds Pumps CV 3196 i-FRAME Installation, Operation And Maintenance Manual Download Page 144

Page: 144 / 178

6.6.12 Install the impeller

CAUTION:

Risk of physical injury from sharp edges. Wear heavy work gloves when handling impellers.

Install the impeller.

Pump size

Action

STi, MTi, and LTi Install the impeller (101). Use a new impeller O-ring (412A).
XLT-i

Install the impeller (101) and a PTFE washer (428D) on the plug (458Y). Use a
new impeller O-ring (412A).

CV 3196

412A

101

126

Figure 134: Install the impeller

Attach a shaft wrench and a coupling key on the shaft.

a) When the impeller (101) makes firm contact with the sleeve (126), raise the shaft wrench

(counterclockwise, viewed from the impeller end of the shaft) off of the bench and slam it down
(clockwise, viewed from the impeller end of shaft).

b) Apply a few sharp raps to tighten the impeller (101).

6.6 Reassembly

142

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

Summary of Contents for Goulds Pumps CV 3196 i-FRAME



















































































































































































Search results

Summary of Contents for Goulds Pumps CV 3196 i-FRAME

Reviews:

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brands by name

Popular brands

ITT Goulds Pumps CV 3196 i-FRAME, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Goulds Pumps CV 3196 i-FRAME

Reviews:

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brands by name

Popular brands