ITT Goulds Pumps CV 3196 i-FRAME Installation, Operation And Maintenance Manual Download Page 145 | Manualshive

Page: 145 / 178

background image

101

Figure 135: Tighten the impeller

3.

Loosen the clamp bolts (370C) and the jack bolts (370D).

4.

Measure the gap between the impeller (101) and the seal chamber and stuffing-box cover (184)
with a feeler gauge.

423

370D

370C

Figure 136: Loosen clamp bolts

5.

When you reach a 0.76 mm | 0.030 in. clearance, tighten the clamp bolts (370C), jack bolts (370D),
and lock nuts (423).
This approximates the impeller position when it is set to 0.38 mm | 0.015 in. from the casing. Per-
form a final impeller adjustment after you install the impeller into the casing.

6.

Check the impeller (101) runout.

Check vane tip to vane tip. If the total indicator reading is greater than 0.13 mm | 0.005 in., deter-
mine the cause and correct the issue before you proceed.

The CV 3196 impeller face is cast, not machined. You do not need to check the face runout.

6.6 Reassembly

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

143

«
...
143
144
145
146
147
...
»

Summary of Contents for Goulds Pumps CV 3196 i-FRAME



















































































































































































Reviews:

No comments

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brand: Jackco Pages: 8

Water Solutions 3098 Series

Brand: Zoeller Pages: 4

Aquanot Spin 508

Brand: Zoeller Pages: 2

Brand: Zoeller Pages: 11

Brand: Zip Pages: 18

Brand: Gardena Pages: 17

Brand: Gardena Pages: 12

Brand: RainWater Harvesting Pages: 3

Brand: CLIVET Pages: 7

Brand: DAXOM Pages: 20

Brand: SAMES KREMLIN Pages: 51

Brand: GE Pages: 28

Brand: Graco Pages: 20

Brand: F.F. Group Pages: 28

Brand: IWAKI PUMPS Pages: 32

sanitary T Series

Brand: TapFlo Pages: 24

Brand: FE PETRO Pages: 16

FLOWMAX PU 2125 F

Brand: SAMES KREMLIN Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands