ITT Goulds Pumps CV 3196 i-FRAME Installation, Operation And Maintenance Manual Download Page 42

Page: 42 / 178

Item Description

Baseplate

Shims or wedges

Grout

Foundation

Sleeve

Dam

Bolt

Figure 29: Pour grout into baseplate

Fill the remainder of the baseplate with grout, and allow the grout to set for at least 48 hours.

Item Description

Baseplate

Grout

Foundation

Dam

Bolt

Figure 30: Fill remainder of baseplate with grout

Tighten the foundation bolts.

4.6 Piping checklists

4.6.1 General piping checklist

Precautions

WARNING:

•

Risk of premature failure. Casing deformation can result in misalignment and contact with
rotating parts, causing excess heat generation and sparks. Flange loads from the piping

4.6 Piping checklists

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

Summary of Contents for Goulds Pumps CV 3196 i-FRAME



















































































































































































Search results

Summary of Contents for Goulds Pumps CV 3196 i-FRAME

Reviews:

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brands by name

Popular brands

ITT Goulds Pumps CV 3196 i-FRAME, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Goulds Pumps CV 3196 i-FRAME

Reviews:

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brands by name

Popular brands