Huawei NetCol5000-C030 Series User Manual Download Page 74

Page: 74 / 215

3.12 Electrical Connection

3.12.1 Overview and Precautions

Precautions

●

Connections of all power cables, control cables, and ground cables must

comply with the local electrical code, and the cable specifications should

comply with the local cabling specifications.

●

For details about the maximum current, see the equipment nameplate.

●

Ensure that the voltage and frequency of the primary power supply meet the

requirements.

●

Only trained and qualified personnel are allowed to connect cables.

●

Before connecting cables, use a multimeter to measure the input voltage and

ensure that the power supply is off.

●

Ensure that all smart cooling products are safely grounded before powering

them on.

●

Keep cables away from the fan, and so on (if unavoidable, take protective

measures), and ensure that cables are securely connected.

●

When laying out cables, ensure that the power and signal cables are reliably

separated and that the strong- and weak-current cables are bound separately.

Layout of the Electric Control Box

Figure 3-46 Electric control box

(1) Grounding position

(2) Fuse

(3) Active power supply

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual

3 Installation

Issue 04 (2021-03-15)

Summary of Contents for NetCol5000-C030 Series
























































































































































































































Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands

Huawei NetCol5000-C030 Series, User Manual

Search results

Summary of Contents for NetCol5000-C030 Series

Reviews:

Related manuals for NetCol5000-C030 Series

Brands by name

Popular brands